Products

1 pcs. Yamaha FUSTB AC-IN BoardFor Europe only: 230VACUsed inYamaha CLP-575 

1 pcs. Korg Kronos Slider VR KnobKorg Kronos 61Korg Kronos 73Korg Kronos 88Korg Kronos Slider VR Knob X09130 SVR KNOB-B/G E40805-2Technical Description of Korg Kronos Slider Knob:This Slider knob will be put on slide potentiometer on your Korg Kronos Synthesizer. There is no tool needed.

1 pcs. Service Kit Kawai WN88 PWB Assy KKB-039This service kit replaces the circuit boards and contact rubbers in the Kawai WN88 keyboard. Only possible as a replacement for keyboards in which contact rubbers with three contacts per tone were used.This set of boards replaces the board KKB-039.The set consists of two boards, fully equipped with new contact rubbers.These Board fit in these e-pianos:Kawai CA65Kawai CA95Kawai CS7Kawai CS10Kawai MP11Kawai VPC1

1 pcs. DESOLDER BRAID Type 400 0.075" 5'We always have very good experiences with this desoldering wire. With the help of this desoldering braid it is possible to pull the solder out of the hole so that the solder legs to be desoldered hang freely in the hole.A really very good and helpful desoldering wire.ESD save.Our tip: With a desoldering pump first remove the main part of the solder and then do the fine work with the desoldering tip.Always ensure adequate ventilation when soldering. 

1 pcs. 26 pin FFC socket with 1.25 mm pitch right angel26 pintop contact sidePitch: 1.25 mmThis FFC Socket is used in Roland JD-800. This is located on small PCB under Keyboard

1 piece EPROM with ROLAND JUNO 1 OS version 4.0 with OLED Support.This OS works only in Juno-1.we offer here a Customized OS version for the Roland Juno1 . This OS version is required if a new OLED display is to be installed in the Juno1 .Mounting instructions for the EPROM in the Roland Juno1 :Soldering may be required if the EPROM in the Roland Juno1 is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

1 piece EPROM with ROLAND JUNO 2 OS version 2.5 with OLED Support.This OS works only in Juno-2.we offer here a Customized OS version for the Roland Juno2 . This OS version is required if a new OLED display is to be installed in the Juno2 .There are two OS versions 2.5Roland released version 2.5 as the last official OS version. This version was then changed again for OLED support. The version number was not incremented. The OS version with OLED support is not an official Roland version.Mounting instructions for the EPROM in the Roland Juno2 :Soldering may be required if the EPROM in the Roland Juno2 is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

Replacement keys for KAWAI Keyboard RH-88Dsuitable forKawai CN35Kawai CN39Kawai ES8Kawai MP7SEThe Kawai RH88D keyboard is a velocity sensitive keyboard with 4-zone hammer action.This keys are weigted.4-zone hammer action:With the 4-zone hammer action, Kawai is trying to get even closer to the feel of a mechanical grand piano than was possible with the previous hammer action keyboards. The keyboard touch of a mechanical piano is different in weight depending on the zone, whether bass or in the high range. This is simulated in the Kawai RH88B keyboard by the fact that there are four different hammers with different weights.The 4-zones are divided as follows:Zone 1, Bass - note 1 to 15Zone 2, middle1 - note 16 to 32Zone 3, middle2 - note 33 to 63Zone 4, soprano - note 64 to 88 

1 pcs. OLED Display New forE-Mu Orbit V1E-Mu Orbit V2These different Display versions are available:BlueRed/OrangeYellowWhiteTechnical Hint for Mounting the OLED Display in E-Mu Orbit:The OLED display is supplied fully wired. The installation is possible without any problems. The display is screwed and the cable is only plugged in. Please make sure that the cable marking is plugged into pin 1 of the connector. Since the new OLED display has a lower height than the original LCD display, we supply washers and new screws to compensate for the height.Plug of Power cable. Don't work under Supply Voltage!!Lifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs.Clavia Nord LCD Display new white Replacement LCD Display for Claiva Nord Instruments. For installation soldering is requiered.Notes on installation for Nord LCD Display:This LCD Display is soldered to a PCB only with a small connector. This requieres very good soldering knowlege. Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 20,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.  

Hammer for a Technics E-Piano, 88 Key HammeractionThe hammers are used and in good condition. All keys supplied by us have been tested.2. different hammer versions:Please pay attention to the details. This Technics keyboard is also available with a pressure point simulation. The hammers in this keyboard version are constructed slightly differently in detail. Please take a close look.Technics has always used the same keyboard for many years. Today it has the advantage that the spare parts are easily interchangeable between the different instruments.We are of the opinion that Technics has used a very good and above all durable keyboard here. In addition to the good sound of the electric pianos, this is a definite plus point in favour of Technics electric pianosAssembly instructions:To be able to use a hammer, the keyboard must at least be unscrewed. This allows the keyboard as a whole to be pushed slightly away from the front edge. Now the key must be unscrewed. The hammer can then be removed from the top. 

1 Pc. Korg Upper Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 1 times.

1 Pc. Korg Lower Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 2 times. 

1 pcs. Kawai Speaker KS08-005 SquawkerNEWsuitable forKawai NV5

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Mono for printed circuit Mono without switch These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Encoder 12 mm footprint and extra short axis suitable for modelsKorg M3Korg OasysKorg TritonKorg Triton leKorg Triton extremeKorg Triton ProKorg Triton ProXThe original encoder used by Korg is no longer manufactured. We offer a replica here. The mechanical dimensions are identical. There are minimal deviations. The detents appear harder than on the original. Practical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Varta 3/V 150 NI-MH rechargeable with 2 solder pin suitable forKorg PolySixKorg Poly-61Varta produces two almost identical batteries of this type. The main difference is the design of the housing.Attention: Shipping for Europe only Dimensions for PCB layout: 17,7 x 10 mmTechnical Description:The dimensions of 3V/150 are hight of 26,8 mm and a deepth of 17,7 mm. The distance between the solder legs is 17,7 mm. The + pol has to legs with a distance of 10 mmThe akku is charged and ready for use.Practical tip:The akku is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Battery with 3 solder pins suitable for  Casio VZ-1Casio VZ-10M

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Small soldering job to do.Color: White Character  /  Black BackgroundDelivery scope of Display Set:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Please let us know your Instrument, so we can put on right cable length onto your Display.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people. 

1 pcs. LCD Display brandnew in Yellow forKorg M1this is  a plug in ready Display replacement for Korg M1. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.Not compatible with M1r. This Display is a separate item.The color of the shown display, may differ from the original.These different Display versions are available:BlueblackWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs Dial Knob suitable forRoland Fantom X6Roland Fantom X7Roalnd Fantom X8

1 pcs. Joystick  Assembly forKorg KROME 61Korg KROME 73Korg KROME 88This Joystick  unit is complete and ready to plug in wired for easy exchanging this unit. To do this work you have to open your instrument. To exchange the unit unplug two connectors and there will be some srews. That is all. 

Slide potentiometer with 30mm travel. Suitable forKorg M3Korg Kronos 61Korg Kronos 73Korg Kronos 88Korg      spare part No.: 500365011400Specifications:Resistance: 10 kOhmtravel: 30 mmTechnical description:The potentiometer has a sliding path of 30 mm. Praktical tip:The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Slide switch with solder Pins for PCB mounting suitable forRoland Juno 106 - DCO,VCF,VCAtechnical Dates:Termination Solder PinSupplied without capPractical advice:Knowledge in soldering is required for switch replacement.