Potentiometer
1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha CLP-545Yamaha CLP-565GPYamaha P-125This potenziometer is used for volume control, but it is a mono potenziometer. Not Stereo and this is correct in this case.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Slider with 45mm Travel. Suitable for Yamaha Motif ESYamaha Montage 6 Main VolumeYamaha Montage 7 Main VolumeYamaha Montage 8 Main VolumeThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
Slider set brand new Sequential Circuits, SCI Potentiometer forSequential Circuits Prophet 5 REV2    Serial 183 - 1300The potentiometers that were installed in the Prophet 5 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 100 KOhmQuantity: 26 pcs.Changes to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread         Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.     The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.
1 pcs. Korg 01/W Volume Slide PotentiometerKorg 01WKorg 01/W FDKorg 01W ProKorg 01/W ProXOEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Nord Rotary Potentiometer vertikal 12 mm with center click, 10kOhm  Electrical properties:The nominal resistance has 10 kilo-Ohm, the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 12 x 11 mm, the total length without pins is 22,5 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 10 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. Replacement stereo rotary potentiometer 14mm widht for Volume, suitable forYamaha RS-7000Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. Rotary Potentiometer for Modulation suitable forYamaha MotifResistance: 10 KOhm
1 pcs. Replacement stereo rotary potentiometer 14mm suitable forKorg KROMEElectrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm widht, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the axis rises with 18 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The six solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.
1 pcs. Slidepotentiometer with center click suitable for Yamaha CLP-150Yamaha CLP-170The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Replacement stereo rotary potentiometer 14mm suitable forYamaha CLP-150Yamaha P-250Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 7,5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. Slider with 45mm Travel. Suitable for Kurzweil PC88The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Rotary Potentiometer C characteristicSubstitute rotary potentiometer forYamaha CP5Electrical properties:C characteristicThe nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. Â
1 pcs. Rotary Potentiometer vertikal 9 mm with center click, 10kOhmSubstitute rotary potentiometer for RoThe rotary pot fits also inKorg KorgElectrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 10 x 12 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of gray plastic. Its head ends in corner radius. The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 11 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. Korg T1 Volume Slide PotentiometerKorg T1Korg T2Korg T3OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Korg Wavestation Volume Slide PotentiometerOEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Korg N1 Volume Slide PotentiometerKorg N1Korg N264Korg N364OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Replacement rotary potentiometer suitable forQuasimidiElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is slotted and Knurled on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. POTENTIOMETER (SLIDE TYPE) A2MSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.
1 pcs. POTENTIOMETER CLP-30Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.
Rotary potentiometer for LCD Contrast adjustment  The potentiometer is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
Rotary potentiometer for LCD Contrast adjustment  The potentiometer is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Rotary Potentiometer vertikal 9 mm with center click, 10kOhmSubstitute rotary potentiometer for RoThe rotary pot fits also inKorg KorgElectrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 10 x 12 mm, the total length without pins is 20 mm. In this total length the casing is 7,5 mm long. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of gray plastic. Its head ends in corner radius. The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 11 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. Replacement stereo rotary potentiometer suitable for volume control inKorg 01R/WElectrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 9,5 mm, the total length without pins is 24 mm. In this total length the casing is 7 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch). Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
1 pcs. Replacement stereo rotary potentiometer 14mm suitable forYamaha PSR-S900Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.Â
Spare parts: Rotary and slider controls, potentiometers.
Rotary and slider controls are among the most commonly used control units on synthesizers, keyboards, organs, electric pianos, samplers, drm computers, and mixing consoles. If they are worn out, the device in which they were installed is often no longer fully usable.
In many cases, such devices end up in the closet, a few months later in the basement, years later, after moisture and dirt have attacked them, in the electronic scrap. This is usually completely unnecessary, because worn or damaged potentiometers can nowadays be replaced in most cases with relatively little effort and at low cost. Often it is only necessary to find the suitable spare part. Here Synth-parts.com is your competent partner and reliable helper. Especially in the case of components discontinued by the manufacturers, we are the help you need. In more than 10 cases we have even reissued controllers that are no longer available. For this purpose, we use the original manufacturers such as Alps, in order to guarantee exact component equality.
The exchange of potentiometers
The exchange of such a component requires of course experience in the handling of appropriate tools, i.e. a soldering iron, but can also be carried out by laymen. However, it must be taken into account that the device in question must often be almost completely disassembled and then reassembled. A camera or cell phone with photo function is an indispensable aid.
Repair in our specialized workshop
If you do not dare to repair the device yourself, or if you want to avoid the effort involved, we naturally offer you the repair in our well-equipped specialist workshop. With our special measuring devices and tools, our well-trained specialists can carry out such work properly and professionally at specially equipped workstations. You can send in your device after previous appointment arrangement, or deliver it directly. We will take care of the rest. Your favorite device is in the best hands with us.
Make an appointment to send in your device.