Products

1 pcs Cage Nut M6 for Rack Mounting  

1 pcs. Encoder 12 mm footprint and extra short axis suitable for models  --  discontinued --Korg M3Korg OasysKorg TritonKorg Triton leKorg Triton extremeKorg Triton ProKorg Triton ProXThis is the original Korg spare PartPractical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Stereo slide potentiometer with 30mm travel and 15mm Lever. Suitable Volume Slider forKorg M3This volume control with the labelling EWANA0X15B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

Volume Slide potentiometer with 30mm travel and 10mm Lever. Suitable forRoland FP-8Roland HP-900Roland HP-1700Roland HP-1700L This Lever is a little bit thinner than the original one.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs.Card Edge Connector 22 Pol suitable forKorg PS3100Korg PS3200Korg PS3300

1 piece bipolar Elko 33uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece bipolar Elko 6,8uF/50V for Speaker NetworksManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The DB series is developt spezial for use in Speaker Networks. Spezial benefit is radial construstion.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. 2SA1015 Transistor 2SA1015PNP Small Signal TransistorHousing print: A1015Housing: TO-92PNPVebo: -5VVcbo: -50VIc:    -150mA

1 pcs. 2SC2240Transistor 2SC2240NPN Small Signal TransistorHousing print: C2240Housing: TO-92NPNVebo: -5VVcbo: -120VIc:    -100mA

1 pcs. Black LCD Display replacement with LED Backlight ready mountedKorg Wavestation,Korg Wacestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementPlease let us now your instrument.The cable must fit specifically to the instrument. Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people. 

1 piece bipolar Elko 470uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Knob for rotary potentiometers inKorg Kronos 61Korg Kronos 73Korg Kronos 88ROTARY VR KNOB (KRONOS) X5870 VR KNOB(H) E30459-1  Specifications:Diameter top:        9 mmDiameter bottom: 10 mmHight:   14 mmShaft:   6 mm, flattedPraktical tip:The knobs are just plugged on. No tools are needed.

1 pcs. FS30KMJ-02Pch Power MOSFET Housing:  TO220VDss:      - 100VId:           - 30APd:          25WTechnical hint:The defect of the power MOSFET is only the secondary fault effect. Conclusion: replacing the MOSFET will not be a long-term fix.

1 pcs. FX30KMJ-03Pch Power FX30KMJ-03 Housing:  TO220VDss:      - 30VId:           - 30APd:          25WTechnical hint:The defect of the power MOSFET is only the secondary fault effect. Conclusion: replacing the MOSFET will not be a long-term fix.

1 piece LED 3 mm Red The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Nut UNF 7/16 Inch for Phone JackTechnical descriptionThis nut fits to 1/4 Inch Phone Jacks. The nut is build from Plastic and has thread UNF 7/16 Inch. The thickness is 6/32 Inch and wrench size is 1/2 Inch. 

1 pcs. Encoder 22 mm suitable for some E-MU Systems instrumentsE-mu ESIE-mu E4XT     depends on manufacturing dateE-mu e6400   depends on manufacturing dateE-mu e-synth ultraE-mu Proteus 1Practical advice:this encoder was used in some few E-Mu Instruments. Please have a look in your instrument first if this is the right one for you. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Rotary Potentiometer vertikal 12 mm with center TapCenter Tap function: no deviation in center positionYamaha RM1x      Utility Mounting instruction Yamaha RM1x:The potentiometer with thread I offer here can also be used in the RM1x. The great advantage of this solution is that I think potentiometers with threads will have much longer lifetime than potentiometers without threads. Indisputably, the axis is guided and stored much more stably by the thread.n the pictures you see a test installation I have made.Electrical properties:The nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 12 mm bright, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has TAP function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

 1 pcs. PP Capacitor 4.7 nF SafetySafety film capacitor suitable for use in mains filters 

1 piece Electrolytical Capacitor 1000uF/50V for Switching Power SupplyManufakturer: NichiconHere i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Yamaha Tyros  Speaker CableThis is a very short cable for direct connection from your Tyros to Speaker on Speaker Stand

1 piece bipolar Elko 4,7uF/50V for Speaker NetworksManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The DB series is developt spezial for use in Speaker Networks. Spezial benefit is radial construstion.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

1 piece Elko 1,000uF/25V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      HPF,VCF FRQ,VFC RES, Bender VCFRoland Juno 60   all, without Arp-Rate, LFO-Rate, Bender DCOElectrical properties:The nominal resistance has 50 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.