Products

1 piece bipolar Elko2.2uF/50V for Speaker NetworksManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The DB series is developt spezial for use in Speaker Networks. Spezial benefit is radial construstion.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Electrolytical Capacitor 33uF/35V for Audio circuitsManufakturer: NichiconSeries: FWHere i offer spezial Capacitor from manufakturer Nichicon. The series FW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

1 piece Electrolytical Capacitor 4700uF/50V for Audio circuits  - discontinued -Manufakturer: NichiconSeries: FWHere i offer spezial Capacitor from manufakturer Nichicon. The series FW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Nut M12 x 1 mm for Phone Jack 1/4

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6     Bender-DCORoland Juno 60    Bender-DCOElectrical properties:The nominal resistance has 1 MOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha PSR-S950Yamaha P-155technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Phone Jack 1/4 inch- 6.3 mm with metall housing, mono with switch, for printed circuit used Roland or Yamaha InstrumentsPay attention! The solder contacts are arranged staggertly.The item is the same as HTJ-064-12IMPHLJ054-01-110Technical description:The offered phone jack for PCB mounting is a mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and metall. Electrical parts are made of a copper alloy with a tin coating. Praktikal tip for phone jack:Pay attention! The solder contacts are arranged staggertly.These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Replacement Keys for Korg LS-88 KeyboardLS-88 keyboard is used inKorg Kronos 2 LS 88This keys are weightedColor: cream white (Ivory)The RealHammer 3 keyboard (RH3) is a touch-sensitive keyboard with 4-zone hammer mechanics.The unweighted keys have a length of 21.4 cm with a width of 2.24 cm. The depth of the key is 5.7 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is not formed on the keyboard but on the hammer. At the back end, the key is held in the keyboard frame by means of a slot. The black keys have a length of 16.4 cm with a width of 1.2 cm. 4-Zone Hammer Mechanics:A 4-zone hammer mechanism is now state of the art for high-quality e-piano keyboards. By means of the four different zones the keyboard manufacturers try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are four different hammers with different weight. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping. Particular mention should be made of the structure of the hammers. The hammers used here are made of a continuous metal part, which should guarantee a long life for these hammers. Only the attached plastic parts appear quite graceful.

1 pcs. Yamaha pedal felt black for E-PianoThe felt is coated with adhesive film on one side. 

Fatar TP100 lower hammer stop felt..This felt is used by Fatar in the TP100 keyboard and dampens the hammers when they return to their resting position after a key is released.In the drawing, the felt marked in red (memory foam).This felt consists of several layers of different materials.For easier installation, this felt is equipped with adhesive tape.  

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg 01/W,Korg 01/W FDKorg 01/W ProKorg 01/W ProXDisplay for Korg 01/RW Rack Modul please order hereWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementThe cable must fit specifically to the instrument. Please let us know your instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01/W Keyboard Version:The instrument must be disassembled almost completely to reach the display.For the new display to work, one SMD resistor on the mainboard of the Korg 01/W must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/W have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Single-pole push switch in the switch design - OFF with solder Pins for PCB mounting suitable for modelsKorg EA-1Korg EMX-1Korg ER-1Korg Part Number: 375014800technical Dates:Voltage: 250VACCurrent: 5ATermination Solder PinVDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for P.C.B. mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha Motif RackYamaha P-120technical Dates:Termination Solder Pinouter Diameter: 7,3 mmInner diameter: 2,9 mm Mechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 3 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

Electrolytical Capacitor Bipolar 1uF/50V SMD Manufakturer: Nichicon The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required""

1 pcs Tactile switch with grey button and red LED suitable for The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Black LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionThis Display fits inNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, minor modifications to the electronics and the power supply are required. This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Replacement Keys for Technics KeyboardsThis Keyboard with single Keys is used by Technics in many of there Keyboards.These Keys are unweigted and in Color Creme White also called Ivory.This parts are used and in a good condition.Important NOTE:For this Keyboard Version Tehnics used different P.C.B.'s and differernt Contactrubber. Please have a exact look on your Keyboard if you need a replacement P.C.B or replacement Contactrubber.

1 piece Elko 22uF/50V for Audio circuits    - discontinued - Manufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Yamaha Pedalcable No6This cable with plug is used by Yamaha for different E-Piano Modells. This Cable fits for Pedal with 3 Pedals.This cabel is for 6 Pol Mini Din Plug. All 6 wires are assigned on both sides.This cable is used in: 

1 pcs Nord LED lens single The LED lens assembly is a crucial component that enhances the visual feedback of the instrument’s control elements. These assemblies are designed for specific models and ensure optimal functionality.Product OverviewFunction: The LED lens assembly serves as a transparent cover that diffuses the light from the underlying LED, providing clear and consistent illumination. This visual feedback is essential for users to monitor parameter changes in real time.Compatibility: The LED lens is used in many Nord models and ensures good visibility of the LEDs.This is a replacement part that we source directly from Clavia Nord.Design: Made from durable materials, the LED lens is designed to withstand regular use while maintaining clarity and brightness.Manufactured from plastic. 

CR2032 / CR2430 with solder tail suitable for YamahaRAM4 CardThis CR2032 is usable as spare part for the original used CR2430 in Yamaha RAM4 Card.Attention: Shipping for Europe only Please check right polarity! Maybe you have to rotate this part about 180 degrees.The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used by  Clavia Nord PianosTechnical descriptionThe offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 piece LED 3 mm Redin 

1 piece Elko 1,000uF/35V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.