Products

1 pcs. Knob for rotary potentiometers inKorg Kronos 61Korg Kronos 73Korg Kronos 88ROTARY VR KNOB (KRONOS) X5870 VR KNOB(H) E30459-1  Specifications:Diameter top:        9 mmDiameter bottom: 10 mmHight:   14 mmShaft:   6 mm, flattedPraktical tip:The knobs are just plugged on. No tools are needed.

Replacement Keys for Korg LS-88 KeyboardLS-88 keyboard is used inKorg Kronos 2 LS 88This keys are weightedColor: cream white (Ivory)The RealHammer 3 keyboard (RH3) is a touch-sensitive keyboard with 4-zone hammer mechanics.The unweighted keys have a length of 21.4 cm with a width of 2.24 cm. The depth of the key is 5.7 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is not formed on the keyboard but on the hammer. At the back end, the key is held in the keyboard frame by means of a slot. The black keys have a length of 16.4 cm with a width of 1.2 cm. 4-Zone Hammer Mechanics:A 4-zone hammer mechanism is now state of the art for high-quality e-piano keyboards. By means of the four different zones the keyboard manufacturers try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are four different hammers with different weight. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping. Particular mention should be made of the structure of the hammers. The hammers used here are made of a continuous metal part, which should guarantee a long life for these hammers. Only the attached plastic parts appear quite graceful.

1 pcs Cage Nut M6 for Rack Mounting  

1 pcs. Encoder 12 mm footprint and extra short axis suitable for models  --  discontinued --Korg M3Korg OasysKorg TritonKorg Triton leKorg Triton extremeKorg Triton ProKorg Triton ProXThis is the original Korg spare PartPractical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs.Card Edge Connector 22 Pol suitable forKorg PS3100Korg PS3200Korg PS3300

1 piece bipolar Elko 6,8uF/50V for Speaker NetworksManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The DB series is developt spezial for use in Speaker Networks. Spezial benefit is radial construstion.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. 2SA1015 Transistor 2SA1015PNP Small Signal TransistorHousing print: A1015Housing: TO-92PNPVebo: -5VVcbo: -50VIc:    -150mA

1 pcs. 2SC2240Transistor 2SC2240NPN Small Signal TransistorHousing print: C2240Housing: TO-92NPNVebo: -5VVcbo: -120VIc:    -100mA

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inKorg Volca Sample 2Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 piece bipolar Elko 470uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Yamaha pedal felt black for E-PianoThe felt is coated with adhesive film on one side. 

Fatar TP100 lower hammer stop felt..This felt is used by Fatar in the TP100 keyboard and dampens the hammers when they return to their resting position after a key is released.In the drawing, the felt marked in red (memory foam).This felt consists of several layers of different materials.For easier installation, this felt is equipped with adhesive tape.  

Single Button 19 x 9  mm, lihgt grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 19 x 9 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. FS30KMJ-02Pch Power MOSFET Housing:  TO220VDss:      - 100VId:           - 30APd:          25WTechnical hint:The defect of the power MOSFET is only the secondary fault effect. Conclusion: replacing the MOSFET will not be a long-term fix.

1 pcs. FX30KMJ-03Pch Power FX30KMJ-03 Housing:  TO220VDss:      - 30VId:           - 30APd:          25WTechnical hint:The defect of the power MOSFET is only the secondary fault effect. Conclusion: replacing the MOSFET will not be a long-term fix.

1 pcs. Yamaha Tyros  Speaker CableThis is a very short cable for direct connection from your Tyros to Speaker on Speaker Stand

1 piece LED 3 mm Red The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Elko 1,000uF/35V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Nut UNF 7/16 Inch for Phone JackTechnical descriptionThis nut fits to 1/4 Inch Phone Jacks. The nut is build from Plastic and has thread UNF 7/16 Inch. The thickness is 6/32 Inch and wrench size is 1/2 Inch. 

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6     Bender-DCORoland Juno 60    Bender-DCOElectrical properties:The nominal resistance has 1 MOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Black LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionThis Display fits inNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, minor modifications to the electronics and the power supply are required. This work is to be done only by technically, best electrotechnically savvy people.  

Replacement keys and spare parts for Fatar TP/7 Keyboard Fatar TP/9 keyboard is a touch sensitive keyboard with unweighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 14,5 cm and a width of 2.24 cm. The thickness of the keys is 1 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  not worked out. The distance from the front side of the key is 9,5 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white.

1 pcs. Rotary Potentiometer vertikal 12 mm with center TapCenter Tap function: no deviation in center positionYamaha RM1x      Utility Mounting instruction Yamaha RM1x:The potentiometer with thread I offer here can also be used in the RM1x. The great advantage of this solution is that I think potentiometers with threads will have much longer lifetime than potentiometers without threads. Indisputably, the axis is guided and stored much more stably by the thread.n the pictures you see a test installation I have made.Electrical properties:The nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 12 mm bright, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has TAP function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo, for printed circuit with Iron FrameThe item is the same asHLJ 0544-01-010Technical description:The offered phone jack for PCB mounting is a mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating.Praktikal tip:Pay attention! The solder contacts are arranged staggertly.These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.