Products

1 piece Elko 470uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Yamaha Montage Super Knob Rotary PotentiometerYamaha Montage 6Yamaha Montage 7Yamaha Montage 8Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

tactile switch suitable for Keypad in these Groovebox'sRoland MC-303Roland MC-307Roland MC-505Roland MC-909   TAPYamaha RS7000Part Number:Roland 125590Yamaha V5914900The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs 65W internal Switching Power Supply Unit brand new, suitable forE-mu E4KE-mu E-SYNTHE-mu E6400E-mu E4 PlatinumE-mu E5000 UltraE-mu E6400 UltraE-mu E4XT UltraDescription:This switching power supply is a perfect replacement for many E-mu devices. In many devices Emu has used the same power supply unit.Our brand new replacement switching power supply has exactly the same mechanical dimensions and the same connectors as the original power supply. Plug and Play.63 Watt power upgrade: The original E-Mu power supply has an output of 43 Watt and must be operated with an internal fan in any case. If extensions such as additional memory or additional drives are installed, the original power supply unit will not be able to supply this power. This is where a power supply upgrade comes in handy.Our 65 Watt power supply unit also needs a fan when the E-Mu is fully extended. Electrical properties:Primary input voltage: 90 - 264 VACRated Power: 63 WattEfficiency: 77%Ripple: 1%Tripple OutputShort circuit protectionEN6100 proofEMC: CLASS BPractical advice:Plug of the device. Don't work under Voltage.Make absolutely sure that the connection cables to the power supply have no contact with the cooling element of the power supply. Due to the development of heat, the insulation of the cable can melt and cause a short circuit or worse tripping. 

Nut M12 x 1 mm for Phone Jack 1/4

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha DGX-660Yamaha P-45technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. HEC2305-016250 DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland EP7 IItechnical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Slide Potentiometer with 30mm Travel. (Custom Built with dust cover for Synth-Parts)Suitable for forRoland JX-3PRoland SH-101      Env Attack, Decay, ReleaseThese potenziometer are brand new ALPS Potentiometer. Additional benefit is a dust cover diectly mounted on housing.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      HPF,VCF FRQ,VFC RES, Bender VCFRoland Juno 60   all, without Arp-Rate, LFO-Rate, Bender DCOElectrical properties:The nominal resistance has 50 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs, Nut M12 x 1 mm black for Phone Jack 1/4\ |Nut M12x1 for Phone Jack ¼ Technical description:The M12x1 nut offered is an accessory for 6.35 mm jack sockets. The nuts are made of iron. Metric fine thread M12 with 1 mm pitch. The nut has a thickness of 2 mm. The spanner size is 14 mm.Very good quality.

Electrolytical Capacitor 10uF/16V SMD Manufakturer: Nichicon  The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Single Button 17 x 7 mm, light grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 piece Electrolytical Capacitor 100uF/63V for Switching Power SupplyManufakturer: Nichicon Here i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 Set. Kawai Sliptape, prepunchedSet with 100 pcs.Size of a sliptape section: 4x12 mm.For old keyboards, the sliptape should be placed in the center because the sliptapes used in earlier times has been larger.This pre-cut sliptape fits only for hammer in plastic keyboards. Do not use this Sliptape in Kawai Wood Keyboards. 

1 pcs. 2SD1733Transistor 2SD1733 BJT NPN SMDThis Transistor is used in Yamaha Mixing Console DM1000We recommend soldering in an additional protective diode 

1 pcs. Nord Pedal Spring  

1 piece bipolar Elko 22uF/50V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. tactile switch suitable for modelsNord ComboNord ElectroNord LeadNord ModularNord PianoNord StageThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece Elko 220uF/50V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Encoder 22 mm suitable for some E-MU Systems instrumentsE-mu ESIE-mu E4XT     depends on manufacturing dateE-mu e6400   depends on manufacturing dateE-mu e-synth ultraE-mu Proteus 1Practical advice:this encoder was used in some few E-Mu Instruments. Please have a look in your instrument first if this is the right one for you. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Parts for Fatar KeyboardsThese parts fits forFatar TP/7SFatar TP/8SFatar TP/9SHere you will find springs, felts, P.C.B., screws

1 pcs. OLED Display blue New forYamaha DX7Yamaha DX9This Display replacement is a really easy swapping. You will only need a screwdriver.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Black LCD Display replacement with LED Backlight ready mountedKorg Wavestation,Korg Wacestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementPlease let us now your instrument.The cable must fit specifically to the instrument. Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people. 

1 piece Elko 22uF/50V for Audio circuits    - discontinued - Manufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.