Products

1 pcs. Yamaha DX5 OLED Display NEW whiteReady-to-plug prepared OLED display for replacement in Yamaha DX5. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Mechanical hints for the replacement of the OLED display in the Yamaha DX5:The mechanical effort required to remove the display from the instrument is relatively simple in this case. The cover of the synthesizer can be lifted up after loosening a few screws. Now the circuit board on which the display is mounted must be unscrewed. The display itself is screwed on and the cable is plugged in.Recommendation:Disconnect the circuitry that generated the backlight voltage for the old display. Simply cut off two components using small side cutters.Instructions are included with the display.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Yamaha TYROS 5 LCL CIRCUIT BOARDSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Fatar TP100 replacement keys whiteThe Fatar TP100 keyboard is a velocity-sensitive keyboard with hammer action.The keys are mounted on a support frame with a plastic core. Contact is made via 12-pin rubber contact strips with two or three graphite points.The unweighted keys are 19.5 cm long and 2.24 cm wide. The key is 1.5 cm thick. The upper resting point on this keyboard is achieved by a hook moulded into the back of the key. The contact actuator, which presses against the contact strip, is 0.2 cm deep. The distance between the contact actuator and the front of the key is 13 cm. At the end, the key tapers into a narrow web. A notch with a round opening is cut into this web. This notch is used to snap the key into the keyboard frame.The hammer, which acts as a counterweight beneath the key, is also hooked into the key. For this purpose, the key has a downward-facing stage. This stage is 47 mm deep from the top edge of the key.Removing and fitting a key:A key is removed by pulling it forwards with moderate force. The key clicks audibly out of the frame.A key is fitted into the frame by snapping it into place with moderate force.This secures the key at the rear end.The keys are white in colour.The plastics used by Fatar tend to darken significantly over time and the plastic becomes somewhat brittle. We currently have second-hand keys in very good condition available.This keyboard is used in products by, amongst others, Doepfer (known for master keyboards and modular synthesisers), Clavia Nord and Waldorf.The keys can be used with double or triple contact rubbers. 

Replacement keys, weighted for Fatar TP/8+ KeyboardFatar TP/8+ keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points. The weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 10,5 mm. The distance from the front side of the key is 13 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked. The keys are in color cream white.

1 pcs 65W internal Switching Power Supply Unit brand new, suitable forAKAI MPC-2000Description:This switching power supply is a perfect replacement for some AKAI Sampler. In some devices AKAI has used the same power supply unit.Our brand new replacement switching power supply has exactly the same mechanical dimensions and the same connectors as the original power supply. Plug and Play.63 Watt power upgrade: The original AKAI power supply has an output of 43 Watt. If extensions such as additional memory or additional drives are installed, the original power supply unit will not be able to supply this power. This is where a power supply upgrade comes in handy. Electrical properties:Primary input voltage: 90 - 264 VACRated Power: 63 WattEfficiency: 77%Ripple: 1%Tripple OutputShort circuit protectionEN6100 proofEMC: CLASS BPractical advice:Plug of the device. Don't work under Voltage.Make absolutely sure that the connection cables to the power supply have no contact with the cooling element of the power supply. Due to the development of heat, the insulation of the cable can melt and cause a short circuit or worse tripping. 

CR2032 / CR2430 with solder tail suitable for YamahaRAM4 CardThis CR2032 is usable as spare part for the original used CR2430 in Yamaha RAM4 Card.Attention: Shipping for Europe only Please check right polarity! Maybe you have to rotate this part about 180 degrees.The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. CR2430 with solder tail suitable forYamaha RAM4 CardPlease check right polarity! Maybe you have to rotate this part about 180 degrees.Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Sanjo Battery with solder tail suitable for  Roland Juno 60Please check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Varta Battery with solder tail suitable for  Roland Juno 60Please check right polarity! Attention: Shipping for Europe only The solder tail is about 0.5mm too wide to fit through the slot in the circuit board.The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

tactile switch suitable for models RolandRoland D-550Roland MKS-50Roland MKS-70Roland Spare Part Number: 13129733The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for Technics E-Pianos and Keyboardssuitable for: PX20PX73PX101PX103PX111PX222PX663PR307KN5000KN6000KN7000 The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsRoland CR-80  (User Controls) The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsKorg Oasys      (Pad Velocity - only one switch needed) The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Jack Circuit QJBG2196 for Technics, usedTechnics SX-PX101Technics SX-PX103Technics SX-PX111Pedal Socket: Mini Din 4 PolThese board is tested by us and fully working. We sell it with one year warranty. 

1 pcs. 230V Switching Power Supply for Korg M1, reconditionedKLM-1269 This Power Supply Board is fully reconditioned, like new. 230V Version

8 position rotary switch 16 mm widht suitable forYamaha RS-7000Mechanical Description:Technical Description:Practical advice:These rotary switch is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Encoder 16 mm widht suitable forTechnics KN6000 Practical advice:The thread of this encoder is 2 mm longer than the thread of the ALPS encoders These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

LCD Display for Roland Fantom XRThis part is no longer available from Roland

LCD Display forRoland Fantom X6Roland Fantom X7Roland Fantom X8

LCD Display forKorg Triton Studio

1 pcs. LCD Display forKorg Radias  - discontinued

1 pcs. LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  yellow BackgroundDelivery scope of LCD Display set:Display ready wiredMounting partsInstruction for replacementPlease let us know your instrument on order.The cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg T1,T2,T3:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people.

1 pcs. Brandnew OLED Display BLUE suitable forYamaha TX802Based on our practical experience, we can offer you a complete mounting kit that contains everything needed to mount the new display. You only need to open the case and replace the OLED display. All you need is a screwdriver. The cable is plugged. This will be delivered:1 Brand new high Quality OLED Display, ready wiredMounting materialsMounting Instructions These different Display versions are available:BlueGreenYellowWhite The color of the shown display, may differ from the original. Installation service:We are also happy to install the display for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 to 100,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. LCD Display brandnew in Blue forYamaha TX802This is  a plug in ready Display replacement for Yamaha TX802. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.On TX802 there is no contrast adjustment possible. We can not guarantee a optimal View. The color of the shown display, may differ from the original. These different Display versions are available:BlackOrangeWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.