Yamaha

One Octave white Replacement Keys for Yamaha GHD KeyboardThis set contains:1 x A1 x B1 x C1 x D1 x E1 x F1 x GNote on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key. 

1 pcs. Yamaha Pedalcable No6This cable with plug is used by Yamaha for different E-Piano Modells. This Cable fits for Pedal with 3 Pedals.This cabel is for 6 Pol Mini Din Plug. All 6 wires are assigned on both sides.This cable is used in: 

CR2032 / CR2430 with solder tail suitable for YamahaRAM4 CardThis CR2032 is usable as spare part for the original used CR2430 in Yamaha RAM4 Card.Attention: Shipping for Europe only Please check right polarity! Maybe you have to rotate this part about 180 degrees.The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Yamaha GHL Actuate Rubber This rubber is used on every singel key as stopperColor: black

Encoder 16 mm widht suitable forYamaha RM1XYamaha RS-7000Practical advice:The thread of this encoder is 2 mm longer than the thread of the original encoders. Depending on the space in the housing, it can tighten a bit when reassembling. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5050 These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Complet replacement set tactile switch for Yamaha RS7000consist of:5 pcs 9,5 mm hight46 pcs 7 mm hight27 pcs Keypad switchOperational Life for all switch: 1.000.000 CyclesThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Yamaha Transistor Array TH3L20 PIANO PLAYERWe offer here a replacement type for the TH3L20 transistor array.This transistor array is used by Yamaha in the disklaviers that work with 110VDC.Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging. 

1 pcs. Power cabel 1,8 m with 2P plug for Europe  

1 pcs. Yamaha GHD A88 Keyboard complete--- shipping only in germany, sorry  -----Please ask if this keyboard is the right one for your e-piano model.This keyboard was used for many years in the vast majority of Yamaha electric piano models.The replacement of the entire keyboard is from a certain age of the electric piano well worth considering.For example, if your original keyboard is affected by the grease problem, you have here an alternative after desen exchange you no longer have to worry about the keyboard.If the keyboard is not in stock, we can order the keyboard from Yamaha. There may be a delivery time.

Pedal Assembly for Yamaha E-Pianos XR780On this Pedal the PCB is fittet with Ground cable.Practice tip:Yamaha has built in a socket on the boards, which are built into the pedal which is perpendicular to the board. Here, the cable is plugged in that leads to the electronics of the electric piano in the upper part. As a result, this beech breaks out in the course of the operating years and it comes to the failure of the pedal.In most Repartur cases, it will be enough just to swap the socket.Depending on the model, this pedal was supplied with a potentiometer or contact rubber in the damper pedal. Please be sure to check the pedal before ordering a replacement part. 

1 pcs. new Contactrubber for Yamaha GHL KeyboardThis keyboard is used in these modells:Yamaha P-35Yamaha P-70Yamaha P-105Yamaha AriusYamaha MOXD8Yamaha MOXF8Color of these Contactrubber may be different.

1 pcs. Yamaha contact PCB for Yamaha GHL88 KeyboardThis keyboard is used inYamaha P-115Yamaha P-125Yamaha YDP-S30Yamaha YDP-143

Replacement Keys for Yamaha GH3 GKS KeyboardThese Keys fits for all Yamaha GH3 GKS keyboards.Yamaha GH3 GKS keyboard is used in:Yamaha Clavinova CLP-440Yamaha Clavinova CLP-525Yamaha Clavinova CLP-625Yamaha Clavinova CLP-635Yamaha Clavinova CVP-605Yamaha Clavinova CVP-701Note on the keys supplied:The keys are manufactured in two different production facilities at Yamaha. Depending on the production of the keys, they have different features. One variant is supplied with black rubber, the other variant without black rubber. In the second case the black rubber has to be taken over from the old key. The key with rubber also has a small fat reservoir. The Yamaha GH3 keyboard is a velocity-sensitive keyboard, which comes in 2 versions.With a 4-zone hammer mechanism and a simple hammer mechanism in which all hammers are equally weighted.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

1 pcs Yamaha FSX Keyboard FFC cable 23 Pol 1,25Keyboard connection cableLength = 130 mmBoth sides have the same connector  

1 piece EPROM with Yamaha DX7 II OS version 1.9we offer here a  OS version for the Yamaha DX7 IIMounting instructions for the EPROM in the Yamaha DX7 II:Soldering may be required if the EPROM in the Yamaha DX7 II is not socketed.In very many cases EPORMs are plugged in on a socket from the factory. But it can happen that the EPROM is soldered directly. In this case the EPROM would have to be desoldered. In this case it is advisable to retrofit the IC socket.Practical notes:IC's/Eproms are sensitive to static charge!Recycling of E-Proms:The best recycling is always the reuse in the original form. We will be happy if you send us back your old eprom. We will then reuse it with the updated OS version. 

1 pcs. Yamaha Tyros  Speaker StandThis housing is made of plastic

1 pcs. new Slide potentiometer with 30mm travel and 15mm Lever. Suitable Slider for Yamaha CS-15    - EG-SYamaha CS-30    - EG1, EG2, EG3Yamaha CS-40    - Sustain  Electrical properties:The nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint:The Lever of the original potentiometer has a conical, tapering shape.

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo with two switch, for printed circuitThis part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Yamaha DX7Technics SX -PX20Technical descriptionThe offered phone jack for PCB mounting is a stereo jack two switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

5 pcs Contact Cleaning Stripes for electrical contacts These contact cleaning stripes are spezial developed for cleaning electrical Contacts.The strip consists of a kind of paper that is quite hard, does not fuzz and is abrasion resistant. The strip was then soaked with a special cleansing solution.

1 pcs Encoder EC24B50D Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

 stereo rotary potentiometer for Volume, suitable forYamaha PSR-330 und 340PSR-530 bis 550PSR-630 und 640PSR-730 und 740PSR-1000, 1100, 1500PSR-2000, 2100, 3000PSR-S700 und S710PSR-S900 und S910Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 6mm. It is made of black plastic. Its head has a slot and ends in corner radius.The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 1 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. FFC cable for Yamaha CVP-209 500 mm length Length = 500 mmPitch= 0,5 mmBoth sides have the same connectorThis cable is used to connect LCD Display with Mainboard inYamaha CVP-207Yamaha CVP-209Yamaha CVP-900The LCD display in the Yamaha Clavinova has vertical stripes in the display?Do you have vertical stripes in the LCD display of your electric piano? These are lines that run from top to bottom through the display and do not belong in the picture.An exchange of this FFC cable can achieve an improvement. In the best case, the vertical stripes are then completely gone. 

1 pcs. Yamaha NL2 Guide CapThis rubber fits in these keyboardsYamaha GH3Yamaha NL2This rubber sits at the head of the key guides and is used for the black deeds and for the white deeds.Color: black