Yamaha

1 pcs. Cable straight thru 12,7 x 11,7 mmThis Cable straight thru is used by 2 pol power cords.Dimensions of mounting hole: 12,7 x 11,7 mm

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo with two switch, for printed circuitThis part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Yamaha DX7Technics SX -PX20Technical descriptionThe offered phone jack for PCB mounting is a stereo jack two switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs Encoder EC24B50D Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Recapping set Power Supply for Yamaha DX7 II ONLY for EU - 230VAVThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Yamaha DX II series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the power supply in the Yamaha DX7 II Spare part number of the PSU board: VB78450 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. LCD Display with LED Backlight replacement including cable Kit forYamaha SY77Yamaha SY99 We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Pleaase let us know your instrument, so we can put on right cable length. Benefits for this Display Replacement with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation this Display in Yamaha SY77 or SY99:The instrument must be disassembled almost completely to reach the display.  This is a very time-consuming process. Please do not underestimate the disassembly and assembly effort.This work is to be done only by technically, best electrotechnically savvy people.No soldering required.All you need is a screwdriver and a side cutter.

1 pcs. Yamaha Tyros  Speaker StandThis housing is made of plastic

Pedal Assembly for Yamaha E-Pianos XR780On this Pedal the PCB is fittet with Ground cable.Practice tip:Yamaha has built in a socket on the boards, which are built into the pedal which is perpendicular to the board. Here, the cable is plugged in that leads to the electronics of the electric piano in the upper part. As a result, this beech breaks out in the course of the operating years and it comes to the failure of the pedal.In most Repartur cases, it will be enough just to swap the socket.Depending on the model, this pedal was supplied with a potentiometer or contact rubber in the damper pedal. Please be sure to check the pedal before ordering a replacement part. 

1 pcs. Yamaha FUSTB AC-IN BoardFor Europe only: 230VACUsed inYamaha CLP-575 

1 pcs. Yamaha DX7 II OLED Display NEW whiteReady-to-plug prepared OLED display for replacement in Yamaha DX7 II. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Mechanical hints for the replacement of the OLED display in the Yamaha DX7II:Please consider in this case that the mechanical effort to get to the display in the instrument is quite high. Among other things, the keyboard and the mainboard must be disassembled. Everything is screwed. No soldering necessary.The display has a cover made of Plexiglass which is glued on the display and has to be transferred to the new display. We have had good experience with the following method: Insert fishing line or sturdy sewing yarn between the display and the cover and use a sawing motion to separate the adhesive.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Black LCD Display with LED Backlight replacementYamaha RM1xWe offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Black BackgroundDelivery scope of LCD Display for RM1x:Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha RM1x :To replace the display, the Yamaha RM1x is opened from the back. So the rear half of the case has to be removed. Afterwards the floppy drive, the DM board and a sheet metal frame must be unscrewed. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife. Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters. Note on contrast adjustment:It may be necessary to replace 2 SMD capacitors on the main board. Due to the ageing of the capacitors, the setting range for the contrast has shifted. 

1 piece LED 3 mm Green The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Complete Set tactile switch suitable for modelsYamaha DX7 IIYamaha DX7 IIFDYamaha Part No: KA907030The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Battery holder for CR2032 for PCB mountingAttention: Shipping for Europe only Technical Description:  Information for handling old Battery's

1 pcs. Yamaha Pedal screwDimensions: M6 x 57 mmNote:At 38 mm, this pedal support bolt has a longer thread than the one under item numberSCYA-WF054500

1 pcs. Yamaha Key emmission circuit Board for Hybrid Pianosthis PCB is used inYamaha MP-100Yamaha GT-1and other Hybrid and Silent Pianos Assembly note:On older instruments, the plastic housing was deeper. To compensate for this, cardboard strips are included with the circuit board. 

1 pcs. black LCD Display brandnew forYamaha TX16Wthis is  a plug in ready Display replacement for Yamaha TX16W. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours.

1 pcs. Power cabel 1.5m with 2P Europlug and solderlugsPower Cord with on side open adn one side Euro PlugOriginal cable fragile or already damaged?For instruments that are 30 years and older, it makes sense to check the power cord. Has the plastic become brittle over the years or is there damage at the kinks of the cable? 

1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha CLP-120Yamaha CLP-430Yamaha CLP-920Yamaha CLP-990Yamaha P-105Yamaha P-120 The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Yamaha USB Socket Typ B PCBJalco used by: Yamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 pcs. Yamaha USB Socket Typ A PCBJalco YKF45-0021used by: Yamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

Yamaha GHL Key's  This keyboard is used in these modells:Yamaha P-120Yamaha P-125Yamaha YDP-S30Yamaha YDP-143Color: whiteNote on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.mechanical construction:Keys for this Keyboard are not available as single keys. One Octave will be a set of three single spare parts. One part for the black Keys. One part for D/A/F, and one part for C/E/F/B.

1 pcs. Rotary Potentiometer suitable forYamaha N1 Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 9.5 x 11 mm, the total length without pins is 29 mm. In this total length the casing is 16 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 10 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of brass. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The nine solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The pins, which are sticking out  are necessary for the electrical function. Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forYamaha QS-300We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Black BackgroundDelivery scope of LCD Display Replacement:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument. Please let us know your instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtion Notes on installation the Display in Yamaha QS-300:The instrument must be disassembled almost completely to reach the display.  This is a very time-consuming process. Please do not underestimate the disassembly and assembly effort.This work is to be done only by technically, best electrotechnically savvy people.No soldering required.All you need is a screwdriver and a side cutter. 

1 pcs Yamaha Contactrubber 88P newThis contact rubber was installed in different Yamaha keyboards and there are different spare part numbers for this spare part.A note about the contact rubbers: The contact rubber for the 88's keyboard was available in the colors pink and green. The pink contact rubber is missing 2 holes in the rubber which serve as a guide.The green version is no longer available.Note for the installation of the Yamaha contact rubber:Please pay attention to the installation position! The interruptions in the Konaktstreifen are not symmetrical.