Replacement Hammer for RH4 KeyboardThe RealHammer 4 (RH4) keyboard is a 4 zone hammer mechanism.This Keyboard is also known as "Natural weighted Hammer Action".

1 pcs Single panel button 19 mm without LED window, for Korg PA4x Do you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive. 

1 pcs. CR2032 with 3 solder pin suitable forKorg DW6000Korg DW8000Korg ix300Korg DVP-1Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version. The positive pole owns two interconnected soldering legs at a distance of 10 mm. The negative pole has one solder leg.We offer these button cell from Company Renata because these producer can provide the required pin distance as the only.Manufacturer:Mitsubishi, Panasonic or VartaPractical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs Ceramic 

Replacement keys and spare parts for Fatar TP/7 Keyboard Fatar TP/9 keyboard is a touch sensitive keyboard with unweighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 14,5 cm and a width of 2.24 cm. The thickness of the keys is 1 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  not worked out. The distance from the front side of the key is 9,5 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white.

Replacement keys and spare parts for Fatar TP/8S Keyboard, weightedWe would like to expressly point out that the keys are used. Fatar keys tend to darken and yellow significantly. Under certain circumstances, it may be that we currently only have very darkened keys in stock.Fatar TP/8S keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 10,5 mm. The distance from the front side of the key is 13 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked.The keys are in color cream white. 

Contact rubber for Korg SK4 KeyboardContactrubber with 12 contacts are discontinued.Strip bright:   26 mmStrip height:     9.5 mmStrip length:  164 / 179   mmNumber of contacts: 12 or 13A rubber contact strip consists of 12 contacts and covers an octave. For the complete exchange of the contact strips in a keyboard with 61 keys 4 contact rubbers with 12 contacts and 1 contact rubber with 13 contacts are required.

Korg Prophecy Mainboard Recapping SetThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.Our recapping set consists of capacitors from renowned manufacturers. Preferably from Nichicon, Würth or Vishay. The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forKorg Wavestation,Korg Wacestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument. Please let us now your instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people.We are proud to offer the thinnest displays available on the market. 

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg 01R/W Rack ModulDisplay for Korg 01/W Keyboard Version plese order hereWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope for LCD Display:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01/RW:The instrument must be disassembled almost completely to reach the display.The rack version of the Korg 01/RW synthesizer has much less mechanical effort than the keyboard versions.For the new display to work, one SMD resistor on the mainboard of the Korg 01/RW must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/RW have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Korg M1 Volume Slider The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

Replacement Hammer for RH3 KeyboardThe RealHammer 3 (RH3) keyboard is a 4 zone hammer mechanism.

1 pcs. Fader knob suitable for:Korg Pa3XKorg Pa3X Pro

Replacement stereo rotary potentiometer suitable for volume control inKorg 05RWKorg TR RackKorg X5DRThis volume control is no longer available by Korg. The here shown replacement pot is build with a 2,5 mm longer axis.Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch). At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Button SmallKorg Kronos 61Korg Kronos 73Korg Kronos 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of  mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. Korg Kronos Slider VR KnobKorg Kronos 61Korg Kronos 73Korg Kronos 88Korg Kronos Slider VR Knob X09130 SVR KNOB-B/G E40805-2Technical Description of Korg Kronos Slider Knob:This Slider knob will be put on slide potentiometer on your Korg Kronos Synthesizer. There is no tool needed.

1 Pc. Korg Upper Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 1 times.

1 Pc. Korg Lower Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 2 times. 

1 pcs. Encoder 12 mm footprint and extra short axis suitable for modelsKorg M3Korg OasysKorg TritonKorg Triton leKorg Triton extremeKorg Triton ProKorg Triton ProXThe original encoder used by Korg is no longer manufactured. We offer a replica here. The mechanical dimensions are identical. There are minimal deviations. The detents appear harder than on the original. Practical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Varta 3/V 150 NI-MH rechargeable with 2 solder pin suitable forKorg PolySixKorg Poly-61Varta produces two almost identical batteries of this type. The main difference is the design of the housing.Attention: Shipping for Europe only Dimensions for PCB layout: 17,7 x 10 mmTechnical Description:The dimensions of 3V/150 are hight of 26,8 mm and a deepth of 17,7 mm. The distance between the solder legs is 17,7 mm. The + pol has to legs with a distance of 10 mmThe akku is charged and ready for use.Practical tip:The akku is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Small soldering job to do.Color: White Character  /  Black BackgroundDelivery scope of Display Set:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Please let us know your Instrument, so we can put on right cable length onto your Display.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people. 

1 pcs. LCD Display brandnew in Yellow forKorg M1this is  a plug in ready Display replacement for Korg M1. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.Not compatible with M1r. This Display is a separate item.The color of the shown display, may differ from the original.These different Display versions are available:BlueblackWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Joystick  Assembly forKorg KROME 61Korg KROME 73Korg KROME 88This Joystick  unit is complete and ready to plug in wired for easy exchanging this unit. To do this work you have to open your instrument. To exchange the unit unplug two connectors and there will be some srews. That is all. 

Slide potentiometer with 30mm travel. Suitable forKorg M3Korg Kronos 61Korg Kronos 73Korg Kronos 88Korg      spare part No.: 500365011400Specifications:Resistance: 10 kOhmtravel: 30 mmTechnical description:The potentiometer has a sliding path of 30 mm. Praktical tip:The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.