1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

1 pcs. slide potentiometer with 30mm travel. Suitable Slider forVolume Control forKorg C150, C350, C3200, C6500Korg ix300, I5SKorg KarmaKorg M50 Master VolumeKorg Oasys 76, Oasys 88Korg Triton EX61, EX76, EX88Korg Triton LE61, LE76, LE88Korg Triton, Triton extremeKorg Triton Pro76, Triton ProXKorg TR76, TR88Korg X50 This volume control with the labelling EWANA0C10B14 is no longer available from the manufacturer Panasonic, because it is no longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.  Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in  Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 piece Contact rubber 12 points for RH3 KeyboardContact high:  7,5 mmStrip bright:   22,3 mmStrip length:  165   mmNumber of contacts: 12A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 88 keys 7 contact strip + 4 pins are needed. The remaining 4 contacts can be easily separated from a rubber contact strip with 12 contacts. A notch is provided in the rubber contact strip after every four contacts for this purpose.

tactile switch suitable for SW1/SW2 in models Korgi30, i30HDOasysTriton, Triton: Le, Extreme, Pro, ProXThese switch is only used for SW1/SW2 at Joystick.Korg Part Number: 375010900The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Replacement stereo rotary potentiometer 12mm widht suitable forKorg EMX1Korg ESX1Not a 1:1 spare part. The original potentiometer is threaded. Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The six solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Cap rectangular for power switchPlease note the dimensions. The original caps used to be larger on many instruments. Dimensions: 12 x 7 mmHight: 10 mm

1 pcs. Mono Slider with 30mm Travel. Suitable for Value Slider for KorgN1, N5, N5ex, N264, N36401W, 01WFDX2, X3, X5, X5dM1, M1r, M3rT1, T2, T3WS, WSEXKorg spare part No.: 365007800The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs Button 19 mm with LED window for Pa4x Do you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19  mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive. 

1 pcs. weighted Key's suitable for Yamaha FS-Keyboardin earlier times this Yamaha Fs Keyboard was also used in Korg Instruments.Please choose your spare part with dropdown menue on left side.Color: cremewhiteThis key is used and in a good kondition  

1 pcs Korg RH3 Keyboard Spring 

Replacement Keys for RH3 KeyboardRH3 keyboard is used inKorg Kronos 73Korg Kronos 88KorgSP-250Korg SV-1 Color: cream white (Ivory)The RealHammer 3 keyboard (RH3) is a touch-sensitive keyboard with 4-zone hammer mechanics.The unweighted keys have a length of 21.4 cm with a width of 2.24 cm. The depth of the key is 5.7 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is not formed on the keyboard but on the hammer. At the back end, the key is held in the keyboard frame by means of a slot. The black keys have a length of 16.4 cm with a width of 1.2 cm. 4-Zone Hammer Mechanics:A 4-zone hammer mechanism is now state of the art for high-quality e-piano keyboards. By means of the four different zones the keyboard manufacturers try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are four different hammers with different weight. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping. Particular mention should be made of the structure of the hammers. The hammers used here are made of a continuous metal part, which should guarantee a long life for these hammers. Only the attached plastic parts appear quite graceful.

1 pcs. Phone Jack 1/4 inch - 6.3 mm, Mono witch switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5076HLJ-2305-01-3030These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsKorg ESX-1 SDKorg SP-170technical Dates:Termination Solder PinOuter Diameter: 5,9 mmInner diameter: 3 mmInner contact: 1.05 mmMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 14 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

Replacement Keys and spare parts for Yamaha AE KeyboardThis part fits for all Yamaha AE Keyboards.Yamaha AE keyboard is used inKorg C-15, C-25, C-30, C-40, C-400, C4000, C-50, C-5500,C6000, C6000MKorg SG-ProXYamaha CLP-122, CLP-550, CLP560Yamaha CVP-20, CVP-50, CVP-55, CVP65, CVP85, CVP87Yamaha AE Keyboard is a very old and one of the first Hammer Action Keyboards. A note on the contact rubbers: The contact rubber for the 88'er keyboard is available in the colors pink and green. The contact rubber in pink is missing 2 holes in the rubber that serve as a mechanical guide.Contactrubber in green is out of production.The interruptions in the contact rubber are not symmetrical. 

Single Button 17 x 7 mm, light grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

Single Button 17 x 7 mm, dark grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs Cage Nut M6 for Rack Mounting  

1 pcs. Encoder 12 mm footprint and extra short axis suitable for models  --  discontinued --Korg M3Korg OasysKorg TritonKorg Triton leKorg Triton extremeKorg Triton ProKorg Triton ProXThis is the original Korg spare PartPractical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Stereo slide potentiometer with 30mm travel and 15mm Lever. Suitable Volume Slider forKorg M3This volume control with the labelling EWANA0X15B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs.Card Edge Connector 22 Pol suitable forKorg PS3100Korg PS3200Korg PS3300

1 pcs. Black LCD Display replacement with LED Backlight ready mountedKorg Wavestation,Korg Wacestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementPlease let us now your instrument.The cable must fit specifically to the instrument. Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people. 

1 pcs. Knob for rotary potentiometers inKorg Kronos 61Korg Kronos 73Korg Kronos 88ROTARY VR KNOB (KRONOS) X5870 VR KNOB(H) E30459-1  Specifications:Diameter top:        9 mmDiameter bottom: 10 mmHight:   14 mmShaft:   6 mm, flattedPraktical tip:The knobs are just plugged on. No tools are needed.

1 pcs. DC Power Plug suitable for modelsKorg electribetechnical Dates:Termination SolderingMechanical Description:The housing of the Power Plug is made of Plastic and cable is soldered on it.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.