1 pcs. Korg SP100 Volume Slide PotentiometerKorg SP100Korg SP200Korg SP250Korg SP300OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

Encoder 16 mm widht suitable forKorg Electribe EMX1       only EC1Korg i2, i3, i4Korg Trinity, Trinity Plus, Trinity ProPractical advice:The thread of this encoder is 2 mm longer than the thread of the Original encoders. Depending on the space in the housing, it can tighten a bit when reassembling. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forKorg 01/WKorg 01/W FDKorg 01/W ProKorg 01/W ProXDisplay for Korg 01/RW rack version please ordere hereWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsone SMD ResistorInstruction for replacementThe cable must fit specifically to the instrument. Please let us know your instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01/W Keyboard Version:The instrument must be disassembled almost completely to reach the display.For the new display to work, one SMD resistor on the mainboard of the Korg 01/W must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/W have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people.This Display is also available with this Colors:Black Character / White BackgroundWhite Character / Black Background 

Replacement Keys for Korg LS-88 KeyboardLS-88 keyboard is used inKorg Kronos 2 LS 88This keys are weightedColor: cream white (Ivory)The RealHammer 3 keyboard (RH3) is a touch-sensitive keyboard with 4-zone hammer mechanics.The unweighted keys have a length of 21.4 cm with a width of 2.24 cm. The depth of the key is 5.7 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is not formed on the keyboard but on the hammer. At the back end, the key is held in the keyboard frame by means of a slot. The black keys have a length of 16.4 cm with a width of 1.2 cm. 4-Zone Hammer Mechanics:A 4-zone hammer mechanism is now state of the art for high-quality e-piano keyboards. By means of the four different zones the keyboard manufacturers try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are four different hammers with different weight. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping. Particular mention should be made of the structure of the hammers. The hammers used here are made of a continuous metal part, which should guarantee a long life for these hammers. Only the attached plastic parts appear quite graceful.

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg 01/W,Korg 01/W FDKorg 01/W ProKorg 01/W ProXDisplay for Korg 01/RW Rack Modul please order hereWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementThe cable must fit specifically to the instrument. Please let us know your instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01/W Keyboard Version:The instrument must be disassembled almost completely to reach the display.For the new display to work, one SMD resistor on the mainboard of the Korg 01/W must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/W have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Single-pole push switch in the switch design - OFF with solder Pins for PCB mounting suitable for modelsKorg EA-1Korg EMX-1Korg ER-1Korg Part Number: 375014800technical Dates:Voltage: 250VACCurrent: 5ATermination Solder PinVDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for P.C.B. mounting. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 12,6 mm, a length of 17 mm and a height of 12.80 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

Korg RH4 Keyboard feltsRH4 keyboard is used in Korg SP-170Korg SP-280Krome 88All felt are fittet with self adhesive tape. For complete replacement of one 88 key keyboard you will need:2x Felt upper5x Hammer felt 12P - L11x Hammer felt L21x Hammer felt L3 

1 pcs. Pitch bend Assembly for Korg Music Production WorkstationKorg KronosKorg Kronos 2Korg Pa3XKorg Pa3X ProKorg Pa4XKorg Pa4X ProKorg Pa300Korg Pa600Korg Pa700Korg Pa900Korg Pa1000This pitch bend unit is complete and ready to plug in wired for easy exchanging this unit. To do this work you have to open your instrument. To exchange the unit unplug two connectors and there will be some srews. That is all. 

1 pc. Korg ESK7 Rubbercontact 6P x1 Features:    Height of contacts: 8 mm    width of the strip:   15 mm    Length of the strip: 80 mm    Number of contacts per strip: 6 contactsOne contact strip consists of 6 contacts and thus covers halfe octave. 

Single Button 17 x 7 mm (No Window)Korg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

LCD Display with LED Backlight replacement including cable Kit forKorg 01/WKorg 01/W FDKorg 01/W ProKorg 01/W ProX We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementPlease let us know your instrumnet. The cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Dislpay in Korg 01/W:The instrument must be disassembled almost completely to reach the display.For the new display to work, one SMD resistor on the mainboard of the Korg 01/W must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/W have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people. 

Recapping set Korg 01/WKorg 01/WKorg 01/W FDKorg 01/W ProKorg 01/W ProXThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Korg 01/W series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the Korg 01/W.The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. slide potentiometer with 45mm travel without center clickKorg EMX-1 ArpeggiatorAttention: Without Center clickElectrical properties:The stereo nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation): The slide potentiometer has a travel of 45 mm. Its metallic casing measures 60 x 8 mm, the height without lever is 7 mm. The lever is made of metall and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 1,2 mm. The solder contact pins are 0,8 mm wide (one of them).In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The value control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 piece Contact rubber 13 points for Korg LS-P88W KeyboardContact high:  9,8 mmStrip bright:   21,5 mmStrip length:  178   mmNumber of contacts: 13A contact strip consists of 13 contacts and there are only these 13 contact rubbers for this keyboard. However, 12 contact rubbers are predominantly used in the keyboard. The contact rubber is then shortened accordingly (cut off).For complete replacement of the rubber contact strips in a keyboard with 88 keys 7,3 contact strip are needed.

Korg M1 recapping set complete unit The Capacitors are firmly soldered to a circuit board. For replacing the capacitors craftsmanship and experience in soldering is required. 

1 pcs Korg PA4x Black panel button 15x7mm, NO LED windowDo you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 15 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive. 

Single Button 19 x 9  mm, dark grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 19 x 9 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. quadruple Button 17 x 6 mm transparent Korg KROME 61Korg KROME 76Korg KROME 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Korg Instruments and is build for a Casing Window of 17 x 6 mm.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

18 pin FFC socket with 2.54 mm pitch18 pinPitch: 2.54 mmLength: 51,18 mmdeepth:  4,50 mmhight:      6,70 mmThese socket is used in Korg Poly 61 between KLM-475 and KLM-476Technical description

1 pcs. Button largeKorg Kronos 61Korg Kronos 73Korg Kronos 88Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of  mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

Single Button 19 x 9  mm, lihgt grayKorg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button build for a Casing Window of 19 x 9 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. Korg Pitch Bend PotentiometerThis is a replacement Poterntiomter for Korg Pitch Bender. This Potetniomter will fit in a realy large range of Korg Instruments.In doubt please compare spare part number with your Service Manual.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):THis Potenziometer is a very spezial part. This one will only fit for Korg Pitch Bend.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs.  18 pin FFC cable with 2.54 mm pitch and 100 mm length18 pinPitch: 2.54 mmLength: 100 mmcontactlength: 7 mmcontacts same sideThese cable is used in Korg Poly 61 between KLM-475 and KLM-476Technical description

5 pcs Contact Cleaning Stripes for electrical contacts These contact cleaning stripes are spezial developed for cleaning electrical Contacts.The strip consists of a kind of paper that is quite hard, does not fuzz and is abrasion resistant. The strip was then soaked with a special cleansing solution.