Keyboards

1 pcs 65W internal Switching Power Supply Unit brand new, suitable forAKAI MPC-2000Description:This switching power supply is a perfect replacement for some AKAI Sampler. In some devices AKAI has used the same power supply unit.Our brand new replacement switching power supply has exactly the same mechanical dimensions and the same connectors as the original power supply. Plug and Play.63 Watt power upgrade: The original AKAI power supply has an output of 43 Watt. If extensions such as additional memory or additional drives are installed, the original power supply unit will not be able to supply this power. This is where a power supply upgrade comes in handy. Electrical properties:Primary input voltage: 90 - 264 VACRated Power: 63 WattEfficiency: 77%Ripple: 1%Tripple OutputShort circuit protectionEN6100 proofEMC: CLASS BPractical advice:Plug of the device. Don't work under Voltage.Make absolutely sure that the connection cables to the power supply have no contact with the cooling element of the power supply. Due to the development of heat, the insulation of the cable can melt and cause a short circuit or worse tripping. 

CR2032 / CR2430 with solder tail suitable for YamahaRAM4 CardThis CR2032 is usable as spare part for the original used CR2430 in Yamaha RAM4 Card.Attention: Shipping for Europe only Please check right polarity! Maybe you have to rotate this part about 180 degrees.The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. CR2430 with solder tail suitable forYamaha RAM4 CardPlease check right polarity! Maybe you have to rotate this part about 180 degrees.Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Sanjo Battery with solder tail suitable for  Roland Juno 60Please check right polarity! Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Varta Battery with solder tail suitable for  Roland Juno 60Please check right polarity! Attention: Shipping for Europe only The solder tail is about 0.5mm too wide to fit through the slot in the circuit board.The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

tactile switch suitable for models RolandRoland D-550Roland MKS-50Roland MKS-70Roland Spare Part Number: 13129733The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for Technics E-Pianos and Keyboardssuitable for: PX20PX73PX101PX103PX111PX222PX663PR307KN5000KN6000KN7000 The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsRoland CR-80  (User Controls) The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsKorg Oasys      (Pad Velocity - only one switch needed) The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Jack Circuit QJBG2196 for Technics, usedTechnics SX-PX101Technics SX-PX103Technics SX-PX111Pedal Socket: Mini Din 4 PolThese board is tested by us and fully working. We sell it with one year warranty. 

1 pcs. 230V Switching Power Supply for Korg M1, reconditionedKLM-1269 This Power Supply Board is fully reconditioned, like new. 230V Version

8 position rotary switch 16 mm widht suitable forYamaha RS-7000Mechanical Description:Technical Description:Practical advice:These rotary switch is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Encoder 16 mm widht suitable forTechnics KN6000 Practical advice:The thread of this encoder is 2 mm longer than the thread of the ALPS encoders These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

LCD Display for Roland Fantom XRThis part is no longer available from Roland

LCD Display forRoland Fantom X6Roland Fantom X7Roland Fantom X8

LCD Display forKorg Triton Studio

1 pcs. LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  yellow BackgroundDelivery scope of LCD Display set:Display ready wiredMounting partsInstruction for replacementPlease let us know your instrument on order.The cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg T1,T2,T3:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people.

1 pcs. Brandnew OLED Display BLUE suitable forYamaha TX802Based on our practical experience, we can offer you a complete mounting kit that contains everything needed to mount the new display. You only need to open the case and replace the OLED display. All you need is a screwdriver. The cable is plugged. This will be delivered:1 Brand new high Quality OLED Display, ready wiredMounting materialsMounting Instructions These different Display versions are available:BlueGreenYellowWhite The color of the shown display, may differ from the original. Installation service:We are also happy to install the display for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 to 100,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. LCD Display brandnew in Blue forYamaha TX802This is  a plug in ready Display replacement for Yamaha TX802. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.On TX802 there is no contrast adjustment possible. We can not guarantee a optimal View. The color of the shown display, may differ from the original. These different Display versions are available:BlackOrangeWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Brandnew OLED Display GREEN suitable forYamaha TX802We have invested a few hours to customize this OLED display so that it can be used in the TX802. Based on our practical experience, we can offer you a complete mounting kit that contains everything needed to mount the new display. You only need to open the case and replace the OLED display. All you need is a screwdriver. The cable is plugged.  This will be delivered:1 Brand new high Quality OLED Display, ready wiredMounting materialsMounting Instructions These different Display versions are available:BlueGreenYellowWhite The color of the shown display, may differ from the original.Installation service:We are also happy to install the display for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 to 100,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

Knob for rotary potentiometers inRoland Fantom FARoland Fantom SRoland Fantom X6Roland Fantom X7Roland Fantom X8Roland Fantom XaSpecifications:Diameter top:       10.4 mmDiameter bottom: 17.8 mmHight:   17.2 mmShaft:   6 mm, flattedPraktical tip:The knobs are just plugged on. No tools are needed.

Dual Button for 12 x 5 mm (No Window)Roland U-20Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 12 x 5 mm. This part has two Buttons.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

Dual Button for 17 x 5 mm (No Window)Roland FP-8Roland U-20Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 17 x 5 mm. This part has two Buttons.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

Single Button for 17 x 5 mm (No Window)Roland U-20Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 17 x 5 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.