Keyboards

1 pcs. Service Kit Kawai RG88B PWB Assy KKB-015This service kit replaces the circuit boards and contact rubbers in the Kawai RG88B keyboard. Only possible as a replacement for keyboards in which contact rubbers with two contacts per tone were used.This set of boards replaces the board KKB-015 The set consists of two boards, fully equipped with new contact rubbers.Compared to the original circuit boards, Kawai has extended the lifespan and refined the dynamic range.It is only possible to exchange this sentence completely. Mixing old boards or contact rubbers with new boards or contact rubbers leads to a malfunction.These Board fit in these e-pianos:Kawai KDP-80Kawai KDP-90Kawai ES100Kawai CN31Kawai CN32Kawai CL-15

Recapping set for Yamaha TX802Attention: 230V EU VersionThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Yamaha TX series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for complete recapping of Yamaha TX802 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

Recapping setYamaha MA60 Recapping Set PSUThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.If no longr available from Nichicon we use Würth or Rubycon Capacitors.This Recapping Set contains all necessary Capacitors for the PSU.The Capacitors are firmly soldered to a circuit board. For replacing the capacitor craftsmanship and experience in soldering is required. 

1 pcs. Lithium batterie 1/2 AA with 2 solder pin suitable for  Attention: EU shipping omlyTechnical Description:The dimensions of 1/2AA are diameter of 14,50 mm and a length of 25 mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version. The distance between the solder legs is 15 mm.Manufacturer: Practical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Yamaha FSX Stopper U 61This FSX keyboard is used in these modells and others:Yamaha Motif XS6Yamaha Tyros 2Yamaha Tyros 3Yamaha Tyros 4   

1 pcs. VR ACTUATOR for Yamaha XR780 Pedal Assembly

1 pcs. Relais NA-5W-K 5Vsuitable forYamaha DKC500

1 pcs. COIL ASS'Y (BL) L=50 WH SX100/RSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Roland PG-1000 OLED Display Blue NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Roland PG-1000 OLED Display Red NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Black LCD Display with LED Backlight replacementYamaha S90We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Black BackgroundDelivery scope of LCD Display for Yamaha S90:Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha S90:To replace the display in the Yamaha S90, remove the screws on the bottom edge. The S90 has a folding mechanism so that the upper part of the housing can be folded upwards. The display is then already accessible. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed.Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife.Mechanically, a piece of a small metal bracket must be sawn off. However, as this metal bracket can be easily removed from the appliance, this is a simple mechanical job.Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters.   

1 pcs. HEC470-01-630 DC Power Jack with solder Pins for PCB mounting suitable for modelsRoland EP7 IIWe offer the original Hosiden power socket here.technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. White LCD Display with LED Backlight replacementRoland MV-30We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: Black Character  /  White BackgroundDelivery scope of LCD Display for MV-30:Display ready wiredInstruction for replacement Advantages of this LCD display compared to the original display from Roland:Modern LED technology for backlightVery good contrast ratioWe now have many years of experience with this type of LCD display. These displays are durable and robust.Notes on installation the Display in Roland MV-30 :To replace the display, the Roland MV-30 is opened from the back. So the rear of the case has to be removed. Afterwards  the Mainboard and Analog Board must be unscrewed. There are a lot of cables to be unpluged, but it is alle pluged in sockets. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Please do not forget to clean the Display Beezel in the housing.No soldering required.All you need is a screwdriver and side cutters.   

1 pcs. blue LCD Display with LED Backlight replacementRoland MV-30We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Blue BackgroundDelivery scope of LCD Display for MV-30:Display ready wiredInstruction for replacement Advantages of this LCD display compared to the original display from Roland:Modern LED technology for backlightVery good contrast ratioWe now have many years of experience with this type of LCD display. These displays are durable and robust.Notes on installation the Display in Roland MV-30 :To replace the display, the Roland MV-30 is opened from the back. So the rear of the case has to be removed. Afterwards  the Mainboard and Analog Board must be unscrewed. There are a lot of cables to be unpluged, but it is alle pluged in sockets. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Please do not forget to clean the Display Beezel in the housing.No soldering required.All you need is a screwdriver and side cutters.   

1 pcs. CIRCUIT BOARD DM CLP-440MSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Yamaha SY35 OLED Display NEW yellow, LCD ReplacementReady-to-plug-in OLED display for replacement in the Yamaha SY35. We have prepared the OLED display for the Yamaha SY35 ready for you to plug in.. You will only need a screwdriver.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Roland JP8000 OLED Display brandnew in red this is  a plug in ready OLED Display replacement for Roland JP8000 Synthsizer. For this display replacement, we strongly recommend shortening the mounting bolts in the housing of the Roland JP8000. The OLED display itself is supplied pre-wired. No soldering is required Mounting instructions for Roland JP8000 OLED:The mechanical assembly of this OLED display is somewhat more complex. The synthesiser is opened from the back and almost all components have to be removed to access the display, unfortunately the keyboard also has to be removed.The display assembly:We have developed a special cable adapter for the display in the Roland JP8000. This makes it possible to continue using the flat cable used in the original. The flat cable is simply plugged in.The display in the Roland JP8000 is mounted on plastic bolts that are firmly connected to the display frame of the synthesiser, but these plastic bolts are much too high for the new OLED display at 8 mm. It is best to shorten these bolts to 5 mm so that the new OLED display comes very close to the windscreen. These plastic bolts can be easily sawn off with a small modelling handsaw. In our picture it is a saw from Tamiya.The big advantage is that a shim can be placed underneath as a height stop. This allows me to saw off the correct height very safely.Scope of delivery Roland JP8000 OLED Display:OLED display ready wiredInstallation instructionsmounting materialThe color of the shown display, may differ from the original.Installation service for Roland JP8000:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Roland JP8000 OLED Display brandnew in green this is  a plug in ready OLED Display replacement for Roland JP8000 Synthsizer. For this display replacement, we strongly recommend shortening the mounting bolts in the housing of the Roland JP8000. The OLED display itself is supplied pre-wired. No soldering is required Mounting instructions for Roland JP8000 OLED:The mechanical assembly of this OLED display is somewhat more complex. The synthesiser is opened from the back and almost all components have to be removed to access the display, unfortunately the keyboard also has to be removed.The display assembly:We have developed a special cable adapter for the display in the Roland JP8000. This makes it possible to continue using the flat cable used in the original. The flat cable is simply plugged in.The display in the Roland JP8000 is mounted on plastic bolts that are firmly connected to the display frame of the synthesiser, but these plastic bolts are much too high for the new OLED display at 8 mm. It is best to shorten these bolts to 5 mm so that the new OLED display comes very close to the windscreen. These plastic bolts can be easily sawn off with a small modelling handsaw. In our picture it is a saw from Tamiya.The big advantage is that a shim can be placed underneath as a height stop. This allows me to saw off the correct height very safely.Scope of delivery Roland JP8000 OLED Display:OLED display ready wiredInstallation instructionsmounting materialThe color of the shown display, may differ from the original.Installation service for Roland JP8000:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. CIRCUIT BOARD, DM PSR8000Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. CIRCUIT BOARD DM CVP-109Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Clavia Nord cape for Encoder older modells Praktical tip:The knobs are just plugged on. No tools are needed. 

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forYamaha VL1MWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation for Display in Yamaha VL1m:No soldering is required. To replace the display in the Yamaha VL1m, the front panel must be largely dismantled. However, this is a relatively simple replacement. No soldering is required. The display is supplied pre-wired.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Nord duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for modelsClavia Nord instrumentstechnical Dates:Voltage: 250VACCurrent: 6ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for soldering. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 15 mm, a length of 30 mm and a height of 9 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forKurzweil PC3K6Kurzweil PC3K7Kurzweil PC3K8We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Notes on installation The LCD Display in Kurzweil PC3XThe original Kurzweil display has different dimensions to today's commercially available displays. We have therefore developed an adapter board to adapt this. We supply the display pre-wired and pre-assembled.This work is to be done only by technically, best electrotechnically savvy people.The contrast of the display can be adjusted as usual using the control in the instrument.No soldering required.All you need is a screwdriver and a side cutter.