Keyboards

1 pcs. LCD Display with LED Backlight replacement including cable Kit forKorg Wavestation,Korg Wacestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  yellow BackgroundDelivery scope of LCD Display:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg Wavestation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people.

1 pcs. Technics ASUB Circuit Board QJBG2298 neuTechnics SXPR-602Technics SXPR-603Technics SXPR-702Technics SXPR-703These circuit board was new desigendimportant note - complex electronic errorFaults in the amplifier circuitry of these Technics electric pianos are very complex and require extensive electronics knowledge and professional experience.A new ASUB board is only part of the solution.Distortion in yourTechnics PR-602,PR-603,PR702,PR703?If you can hear sound distortions in your Technis electric piano, then it can often be due to a defect in the small additional circuit board ASUB on the amplifier board QJBG2298.If there is no sound at all then the fault is bigger and a replacement of only the ASUB is wrong. First fix the larger defect.We do not assume any warranty if a new ASUB board is inserted into a defective amplifier.Electrostatic sensitive assembly:Once the packaging has been opened, the assembly cannot be returned.What to do with the old, defective ASUB?we are happy if you send us back your defective ASUB. We will repair these boards and return them to their original use.

1 pcs. OLED Display New forE-Mu Ultra ProteusTo replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Kawai Button Duo large 14 x 8 mmKawai MP-8Kawai MP-11Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description of Kawai Button:This Button fits for many Kawai Stage Pianos and is build for a Casing Window of 14 x 8 mm. This part has two Button. It is used with 5 mm tact switch.Practical tip:This button sits between PCB and Cassis. Normaly the button is fixed with tape.

1 pcs. Kawai Button Duo Small 11 x 8 mmKawai ES-7Kawai MP-8Kawai MP-11Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description of Kawai Button:This Button fits for many Kawai Stage Pianos and is build for a Casing Window of 11 x 8 mm. This part has two Button. It is used with 5 mm tact switch.Practical tip:This button sits between PCB and Cassis. Normaly the button is fixed with tape.

 1 pcs. Cap round 12 mm for tact switchThis cap for stylus has a diameter of 12 mm and a receptacle of 3 x 3 mm.Suitable as a spare part for E-Mu sampler

1 pcs. LCD Display with LED Backlight replacement including cable Kit forYamaha QS-300 We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Pleaase let us know your instrument, so we can put on right cable length. Benefits for this Display Replacement with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation ths Display in Yamaha QS-300:The instrument must be disassembled almost completely to reach the display.  This is a very time-consuming process. Please do not underestimate the disassembly and assembly effort.This work is to be done only by technically, best electrotechnically savvy people.No soldering required.All you need is a screwdriver and a side cutter.

1 pcs. Rotary Potentiometer for pitch bendThis poti is used inYamaha MOX6Yamaha MOX8

1 pcs. LCD Display with LED Backlight replacement including cable Kit forYamaha W5Yamaha W7 We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Pleaase let us know your instrument, so we can put on right cable length. Benefits for this Display Replacement with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation ths Display in Yamaha W5 or W7:The instrument must be disassembled almost completely to reach the display.  This is a very time-consuming process. Please do not underestimate the disassembly and assembly effort.This work is to be done only by technically, best electrotechnically savvy people.No soldering required.All you need is a screwdriver and a side cutter.

1 pcs. Encoder 16 mm wide suitable forWaldorf Microwave 2The Waldorf Microwave II has 4 of these encoders without detents. These encoders are mounted below the display.Practical advice:The axis of this encoder is 2 mm longer than the axis of the original encoder of the Waldorf Microwave 2. Under circumstances the axis must be shortened. Since the axis of the encoder is made of plastic, shortening is quite easy.These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 02Roland D-70, mainboard version 03We offer here a high quality replacement display with modern LED technology for the backlight.Color: black font/white backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description! Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland D-70:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", "02" or "03". 

1 Stk. LCD display with LED backlightsuitable forRoland D-70, mainboard version 00Roland D-70, mainboard version 01We offer here a high quality replacement display with modern LED technology for the backlight.Color: black font/white backgroundScope of delivery:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description!Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", or "02". 

1 pcs. new Korg LS88 PCB Assy KeyboardThis keyboard is used inKorg Kronos 2 LS88this is set of three contact PCB as used in Korg Kronos 2 LS88.This set contains LOW, MID ans HIGH contact PCB.This Set is KLM-3543, KLM-3544, KLM-3545. 

1 piece Yamaha Pedal PCB X0193 for E-Pianos V7675600This PCB for Yamaha pedal unit is used in pedals in which three potentiometers are installed.For final use, parts on the board still have to be broken off. The break edges are marked and perforated accordingly. This can be done easily and without tools. 

1 pcs external Power Supply Unit Kawai PS-129Mechanical Description:The primary plug is designed for Europe and the plug on the secondary side is round with 6.5 mm outside diameter.Delivery only with secondary cable.Electrical properties:Primary: 100-230V ACSecundary: 12V DCCurrent: 4AUse: EuropePractical advice:Plug of the device. Don't work under Voltage. 

1 pcs. Korg 01/W Data Entry SliderKorg 01/WKorg 01/W FDKorg 01/W ProKorg 01/W ProXOEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Replacement rotary potentiometer suitable forQuasimidiElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is slotted and Knurled on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. IC Socket DIP 28 Gold for ICTechnical Hint:Mounting of this part requiers soldering.  

1 pcs. Yamaha DKC100 Controller PCB X1047Controller PCB in Userpanel DKC100Used inYamaha Disklavier HQ100SYamaha Disklavier MX100 II

1 pcs. Floppy2USB Emulator suitable for Technics KN6000 We deliver this Floppy2USB drive with a suitable adapter cable. The installation is easy to accomplish.Much more complex is the transfer of the floppy disks to the USB stick. This requires an old PC that still has a floppy drive and a USB post. Here there is a software that supports copying.

1 pcs. OLED Display brandnew in yellow forRoland D-550this is  a plug in ready Display replacement for Roland D-550. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation:We deliver this OLED dislpay for the Roland D-550 synthesizer ready for installation. All necessary cables are already soldered on. You will only need a screwdriver for the installation.- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Roland D-110 OLED Display NewReady to plug in OLED display for replacement in Roland D-110 . No soldering is required.Roland has built a display into the D-110  that is no longer available today. Above all, a mechanical adaptation to today's available OLED display is required.We have developed a mounting frame that allows the use of today's standard display. We have this frame specially manufactured.For the actual assembly of the new OLED display in the Roland D110 only a screwdriver is required.Scope of delivery of the OLED Display Set:OLED Display ready wiredMounting FrameInstructionsPlease choose you favorit color. Lifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 to 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Yamaha Spezial Keyboard grease, 50gOriginal Yamaha plastic grease for Keyboards. Yamaha now also uses the blue key grease like in the GHD keyboards at this point.Grease will be delivered in a 50 gramm tube.This grease is used on Yamaha PSR Series. The original grease was probably a white grease. 

1 pcs. CCFL neon lamp 100 x 2,2 mm with cape  for LCD Display BacklightYamaha PSR-S700Yamaha PSR-S900Safety advice to CCFL tubes:These neon tubes are very sensitive. Handling and mounting must be done very very carefully.The fluorescent tubes are operated with a high voltage of approx. 180V AC. Please observe the corresponding safety regulations of the VDE.