Keyboards

1 pcs. Clavia Nord Knob with line 6 mmPraktical tip:The knobs are just plugged on. No tools are needed. 

1 pcs tactile switch 7 mm suitable forAlesis AndromedaWe offer here a tactile switch for Alesis that has the same technical features as the original one.The switch are soldered onto a circuit board. Manual dexterity and experience in soldering are required to replace the switches.why should I solder new pushbutton 

1 piece bipolar Elko 4,7uF/50V for Audio circuits  - Discontinued -Manufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Replacement rotary potentiometer suitable for Alesis Andromeda A6   -  Post FilterWe have set out on a search!Alesis used potentiometers manufactured by Panasonic in the Andromeda A6. Unfortunately, Panasonic has stopped the production of this potentiometer series. In addition, there is the fact that the potentiometers from Panasonic have a few special features so that most commercially available potentiometers can not be used.After a lengthy research, which unfortunately did not lead to a positive result, we decided to build a potentiometer especially for the Alesis Andromeda A6.Shaft and guide are made of metal: We deliberately chose a potentiometer with a metal shaft and guide. We are convinced that this leads to a much longer life span than the original Panasonic potentiometers where shaft and guide are made of plastic.Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 9 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 17,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:67 pcs. - to replace all small Potentiometer in your Alesis Andromeda A6 you will need 67 of these.The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

tactile switch suitable for KorgThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Kawai Sliptape, stripeThis Sliptape is for old and new wood Keys.8 contiguous strips are delivered which are cut to size. This amount is enough for more than one keyboard. So you can also cut something.You will find here a Blog articel for this Item:Sticky key on Kawai E-Piano Practical Hint for Kawai Sliptape:When replacing the sliptapes on the wooden keys, you have to be extremely accurate and meticulous. Especially the removal of glue residues on the hammer heads is extremely important. 

1 pcs tactile switch suitable for Roland JD800These switch is for User ButtonsRoland Part Number: 13169727The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece tactile switch suitable for modelsAKAI MPC-500AKAI MPC-1000AKAI MPC-2000AKAI MPC-2500AKAI MPC-4000Akai Part Number:  ES-349474 und ES-411687NThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Phone Jack 1/4 inch - 6.3 mm, stereo with 2 switch, printed circuit for Korg, Roland or Yamaha Instrumentsthis Phone Jack corresponds to these parts:YKB21-5006HLJ-4306-01-3040HTJ-064-04These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Contactrubber GH3 suitable for Yamaha This keyboard is used in these modells:Yamaha CVP-305Yamaha CVP-307And much more other Modells.For a complete Keybord with 88 keys you will need this quantity on contactrubber:1 x 5 contacts6 x 12 contacts1 x 11 contacts 

1 pcs. Piano felt as alternative to Kawai sliptapeOur alternative for the sliptape used by Kawai for wooden keys.Our alternative to the slip tape used by Kawai for wooden keys.Piano felt, an old and proven product from piano making. This piano felt is used by every piano maker exactly where mechanical resilience is required. Where a lever movement is converted into a rotary movement and mechanical parts should slide over each other as silently as possible.In the Kawai digital pianos in which wooden keys are used is exactly such a mechanical load given from Kawai with a so-called Sliptape is padded. This piano felt here is best suited to replace the Kawai sliptape.Compared to the original Kawai Sliptape, the key pressure on this felt is very slightly more sluggish. However, this should improve with use as the felt becomes smoother with use.What else you need:1 cutter knifePonal expressAlcohol for cleaningPolishing pasteThe felt strip supplied is more than sufficient for one keyboard with 88 keys. 

Contact rubber 12 points for RH4 Keyboard    Contact high:  7,5 mmStrip bright:   22,3 mmStrip length:  165   mmNumber of contacts: 12Roland Part Number: 4671145A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 88 keys 7 contact strip + 4 pins are needed. The remaining 4 contacts can be easily separated from a rubber contact strip with 12 contacts. A notch is provided in the rubber contact strip after every four contacts for this purpose.

1 pcs. Service Kit Kawai RH88B PWB Assy KKB-044(2)This service kit replaces the circuit boards and contact rubbers in the Kawai RH88B keyboard. Only possible as a replacement for keyboards in which contact rubbers with three contacts per tone were used.This set of boards replaces the board KKB-040.The set consists of two boards, fully equipped with new contact rubbers.Compared to the original circuit boards, Kawai has extended the lifespan and refined the dynamic range.It is only possible to exchange this sentence completely. Mixing old boards or contact rubbers with new boards or contact rubbers leads to a malfunction.These Board fit in these e-pianos:Kawai CS4Kawai CN24Kawai CN25Kawai CN27Kawai CN29Kawai CN34Kawai CN35Kawai CN37Kawai CN39Kawai ES7Kawai ES8Kawai ES920Kawai MP7Kawai MP7SEClavia Nord Grand

1 piece bipolar Elko 47uF/50V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. CR2032 with 2 solder pin suitable forYamaha DX7, DX7 II, DX9, DX27, DX100Yamaha TG77Yamaha RX5, RX7, RX11Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Due to the soldering legs, the installation height is 6 mm for this horizontal version. The distance between the solder legs is 15 mm.Manufacturer: Panasonic or VartaPractical tip:The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos     -   MIX SectionRoland MC-909Yamaha RS-7000   - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. tactile switch suitable for modelsKorg MonopolyKorg PolySixKorg BX3/CX3      first Version build in 1980'sRoland JX 10PRoland Jupiter 8Roland TR808Part Number: Korg: 37503400, Roland: 13169601The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsNord ComboNord ElectroNord LeadNord ModularNord PianoNord StageThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs tactile switch suitableYamaha RM1XYamaha MX100II disklavierThese switch is for Keyboard ButtonsYamaha Part Number: VS1809800The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece LED 3 mm Blue This LED is a technical equivalent to the orignial Korg LED's.The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Xvive MN3007 1024 Stage BBD DIP8  -  Panasonic MN3007 cloneRebuild of the MN3007 BBD from Panasonic. We think that it is a 1:1 clone from original Panasonic Chip. Features of MN3007Variable delay time from 5.12ms to 51.2msWide dynamic range 80dB (typ)Total harmonic distortion <0.5%Clock frequency from 10Hz to 100KHz Package: DIP-8 Mechanical Description of MN3007:The IC is housed in a DIP 8 package and is designed for trughhole mounting on a circuit board. THis chip is pin compatible to Panasonic MN3007.ICs are sensitive to static charge! Handle with care. Semiconductors are excluded from exchange.   

1 pcs. Yamaha GH3 Actuate RubberThis rubber fits in these keyboardsYamaha GHDYamaha GH3Yamaha NL2This rubber is used on every single key as stopperColor: black 

1 pcs. Clavia Nord Volume Dreh Potentiometer Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 16 mm Diameter, the total length without pins is 32 mm. In this total length the casing is 9 mm long. On this casing is the thread with 7 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 4 mm and is flattened on a length of 12 mm. It is made of metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. tactile switch suitable for models Korgis40, is50Pa1 XPro, Pa2 XProPa50                        without LCD BoardPa60, Pa80, Pa500, Pa800SP200Korg Part Number:  INT0001008The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton