Keyboards

1 pcs tactile switch suitable for E-Mu e4K              all exept   Rec,Play,Stop,RW,FWE-Mu E-Synth       all exept   Rec,Play,Stop,RW,FWE-Mu E4-XTE-Mu e6400Launch PadThis is exactly the same switch used by E-Mu on manufacturing. On this switch i am not satisfied with life span.why should I solder new pushbutton

1 pcs. Screw 16 mm Black PhillipsLength: 16 mm Material: Iron blackThis Screw is used in many Clavia Nord instrumnets as Housing screw. This one is used for red side panels.

1 pcs. Screw 6 mm Black PhillipsLength: 6 mm Material: Iron blackThis Screw is used in many Clavia Nord instrumnets as Housing screw. This one can be located on rear side or on bottom.

1 pcs. IC Socket for D5534ATechnical Hint:The IC socket has 17 legs with a grid of 2 mm. The IC D5534A has 16 legs + an empty position as a built-in marker. I think it makes sense to take over this empty position for the IC socket as well. The corresponding soldering pin can be easily pushed out.Mounting of this part requiers soldering. 

1 pcs. Yamaha Pedalcable No1This cable with plug is used by Yamaha for different E-Piano Modells. This Cable fits for Pedal with 3 Pedals.This cabel is for 6 Pol Mini Din Plug. 5 wires are assigned on both sides.This cable is used inYamaha CLP-440

Tactile switch suitable forSequential Circuits Prophet VSThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Slide potentiometer with 20mm travel. Suitable forSchiebepotentiometer Juno 106 - BenderAppearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements.The slide potentiometer has a travel of 20 mm.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Quasimidi LED-tactile switch suitable for modelLED colour: Red We offer here switch from the second redesigned series where LED body is clear.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Stereo slide potentiometer with 30mm travel and 10mm Lever. Suitable Slider forVolume Control forRoland D10Roland D20Roland D50Please note: the original lever (sliding pin) is slightly thicker.The cap will sit loosely with the new Potentiometer. This can be remedied with a little paper, for example. Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Single-pole push switch in the switch design - OFF with solder terminals for cable assembly suitable for modelsKorg M1, M1RKorg T1, T2, T3Korg Part Number: 375006100The power switch corresponds to the ALPS switches SDDLD10900 TV5. This is no longer manufactured by ALPS.Termination Solder LugMounting holes with threadVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for a screw in a housing and has two threaded holes for M3 x 0.5 screws. The spacing of the mounting holes is 20 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 5 A at 250 VAC.Knowledge in soldering is required for switch replacement.

Tactile switch suitable for  The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.Why should I solder new pushbutton

LED-tactile switch suitable for modelRoland TR-909LED colour: RedRoland replacement part no.: 13169627The construction part is not longer built. The old serial number was KHJ-11901. With that serial number the part was built during the 80s.We offer here switch from the second redesigned series where LED body is clear.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Yamaha Pedalcable No3This cable with plug is used by Yamaha for different E-Piano Modells. This Cable fits for Pedal with 3 Pedals.This cabel is for 6 Pol Mini Din Plug. All 6 wires are assigned on both sides.This cable is used in:Yamaha CLP-745Yamaha CLP-810SYamaha CLP-840Yamaha CLP-860Yamaha CLP-990Old Manufacturer Number: V0044700

1 pcs. tactile switch suitable for modelsRoland MC-505Roland MC-808Roland MC-909Roland Part Number:  1343478The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. tactile switch suitable for modelsYamaha W5Yamaha W7 The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. slide potentiometer with 30mm travel. Suitable Slider forVolume Control forKorg C150, C350, C3200, C6500Korg ix300, I5SKorg KarmaKorg M50 Master VolumeKorg Oasys 76, Oasys 88Korg Triton EX61, EX76, EX88Korg Triton LE61, LE76, LE88Korg Triton, Triton extremeKorg Triton Pro76, Triton ProXKorg TR76, TR88Korg X50 This volume control with the labelling EWANA0C10B14 is no longer available from the manufacturer Panasonic, because it is no longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.  Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. SMK LGP6531-0800F DC Power Jack with solder pins for PCBtechnical Dates of LGP6531-0800F:Termination Solder PinOuter Diameter: 5.9 mmInner Diameter: 3 mmInner Contact: 1.05 mmDC-Socket LGP6531-0800F and LGP6531-1500f are nearly same. LGP6531-0800f is a little bit better with electrical contact.Mechanical Description of LGP6531-0800F and LGP6531-1500F:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 14 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

SMD tactile switch suitable for models KorgPa50         only LCD BoardKorg Part Number:  MP5010102Attention: SMD (Surface Mounted Device) needs spezial soldering equipment and spezial experience in solderingDimensions:Length: 6mmDeep:   6mmhigh:    5mmThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

 1 pcs. PP Capacitor 22 nF Safety

1 pcs. Yamaha Pedal PotentiometerThis is a replacement Poterntiomter for Pedal from E-Piano if there is a Volume Pedal installed.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Pedal.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. Yamaha Reface MIDI cable forYamaha Reface CPYamaha Reface CSYamaha Reface DXYamaha Reface YCthis is a special MIDI cable for Yamaha Reface CP Synthesizer. Because of small housing Yamaha used here a MINI DIN plug.Adapter cable: The cable is provided with a MINI DIN plug on the side to the synthesizer from which the two usual 5-pin DIN sockets are then led out. 

Recapping set Power Supply for Yamaha DX7,DX9The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Yamaha DX series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the power supply in the Yamaha DX7, DX9. Spare part number of the PSU board: LC90330 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Contactrubber 16M CT2M suitable for Yamaha This keyboard is used in these modells:Yamaha PSR-270Yamaha PSR-340Yamaha PSR-640Yamaha PSR-740Yamaha PSR-S700Yamaha PSR-S710Yamaha PSR-S750Yamaha PSR-S770Yamaha PSR-S900Yamaha PSR-S910Yamaha PSR-S950Yamaha PSR-S970Yamaha PSR-1500Yamaha PSR-2000Yamaha PSR-3000These Contactrubber was buildt in two different colors. Function is in both cases the same. 

1 pcs. Yamaha Headphone HPE170 EAR PAD ASSYThe ear cups have a narrower opening for attaching them to the headphones. The replacement procedure requires a bit of force.The Yamaha HPE-170 headphones were launched in 1993. We offer here one new ear cup, suitable for the Yamaha headphones HPE170. The ear pad is a original Yamaha spare part.