Keyboards

1 pcs. new Korg RH4 PCB Assy KeyboardThis keyboard is used inKorg Krome 88Korg SP-280RH-4, RH-4L or RH-4HL—one letter—big difference. Please note.this is set of three contact PCB as used in Korg RH-4.This set contains LOW, MID ans HIGH contact PCB  - KLM-2949/2950/2951 The circuit board is partially supplied with a blue protective film over the contacts. This protective film must be removed before installation. 

1 pcs 45W internal Switching Power Supply Unit suitable forKorg SV1Electrical properties:Primary input voltage: 90 - 264 VACRated Power: 45 WattEfficiency: 77%Ripple: 1%Tripple OutputShort circuit protectionEN6100 proofEMC: CLASS BPractical advice:Plug of the device. Don't work under Voltage.  

1 pcs. PUSH SWITCH SPPH23 HQ SerieSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forKurzweil PC3K6Kurzweil PC3K7Kurzweil PC3K8We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementNotes on installation The LCD Display in Kurzweil PC3XThe original Kurzweil display has different dimensions to today's commercially available displays. We have therefore developed an adapter board to adapt this. We supply the display pre-wired and pre-assembled.This work is to be done only by technically, best electrotechnically savvy people.The contrast of the display can be adjusted as usual using the control in the instrument.No soldering required.All you need is a screwdriver and a side cutter. 

1 pcs. ITT SAJ110 - 7 Stage Frequency Divider ICOld stock - every single component has been checked by us for function.Housing is manufactured in red and black. FeaturesClock frequency from 20Hz to 20KHz Package: DIP-14    Mechanical Description of SAJ110:The IC is housed in a DIP 14 package and is designed for trughhole mounting on a circuit board.ICs are sensitive to static charge! Handle with care. Semiconductors are excluded from exchange.  

1 pcs. Roland MC505 Potentiometer Part MixerDrop In Potentiometer for Section Part Mixer in Ronad MC-505. The lever must be shortened by 5 mm so that it fits in the Roland MC505. This can be done quite easily with a side cutter. Best to be done before soldering.This Fader with the labelling EWANKEC10B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of metall and ends in corner radius. Its height is 10 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The potetniometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 Pc Korg Top Keystroke Felt for Electric Piano KeyboardsThis felt is used by Korg in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 4 times.

1 pcs Korg PA4x Black rotary knob, with white indicator dot, 12mm in diameter   

1 pcs Korg PA4x Red panel button 19 mm with LED windowDo you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive. 

1 pcs Nord LED lens surround 6 The LED lens assembly is a crucial component that enhances the visual feedback of the instrument’s control elements. These assemblies are designed for specific models and ensure optimal functionality.Product OverviewFunction: The LED lens assembly serves as a transparent cover that diffuses the light from the underlying LED, providing clear and consistent illumination. This visual feedback is essential for users to monitor parameter changes in real time.Compatibility: The LED lens is used in many Nord models and ensures good visibility of the LEDs.This is a replacement part that we source directly from Clavia Nord.Design: Made from durable materials, the LED lens is designed to withstand regular use while maintaining clarity and brightness.Manufactured from plastic. 

1 Pc Technics Top Keystroke Felt for Electric Piano KeyboardsThis felt is used by Technics in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 4 times.

1 Pc. Technics Lower Hammer Stop Felt for Electric Piano KeyboardsThis felt is used by Technics in many keyboards and dampens the hammers when they are moved against the frame when a key is pressed. This felt consists of several layers of different materials. For better assembly, this felt is equipped with adhesive tape. The felt is designed for an 88-key keyboard. If you have the 73 key version, the felt can be shortened.For a complete 88 key keyboard, you need this part 2 times. 

1 pcs Button single 17 mm with LED window for Pa4xDo you know this: the button you activate don't react. This process starts slowly and in the beginning do don't recognise it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive. 

1 pcs. Encoder 12 mm footprint and switch suitable for modelsRoland Fantom XRPractical advice: These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. new LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementPlease let us know your instrument. The cable must fit specifically to the instrument. Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people. 

Rotary potentiometer for LCD Contrast adjustmentThis pot is for these models:M1, M1r, M3rT1, T2, T3WavestationKorg spare part No.: 360021200The potentiometer is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

Mini Din plug male 4 pin for printed circuitthis mini din plug is used by Technics E-Pianos for connecting foodswitch. Technics used two different Mini DIN plugs. It can be a 4 pole or a 8 pole version.These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Single pole rocker switch with solder lugs suitable for modelsKorg MonoPolyKorg PolySixKorg Part Number: 375016006A / 250VACTermination Solder Lug1 poleMounting hole: 19,8 x 12,8 mmDimensions outside: 20,8 x 14,8 mmVDE-tested Mechanical Description:The switch housing consists of polycarbonate. The switch is provided for a snap-in mounting in a housing and having corresponding spring lips on the narrow side of the housing. Housing cutout for installation should be 19.30 mm x 12.90 mm. The switch itself has a width of 12.90 mm, a length of 18.50 mm and a height of 13.60 mm plus 3 mm height of the rocker. The outside dimensions are 20.8 mm x 14.8 mm.Electrical properties:The electrical components are made of copper with a silver or tin plating and electrical connection is made with solder lugs for cable assembly. The length of the terminals is 2.9 mm with a width of 3 mm.The electrical load is 6 A at 250 VAC.Knowledge in soldering is required for switch replacement.

1 pcs. Tactile switch with orange button and red LED suitable forSequential Circuits Prophet VS The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece LED 2 mm Green The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Electrolytical Capacitor 1uF/50V SMDManufakturer: NichiconSerie: UQ for Audio Especially with SMD Elkos we often have the experience that these Elkos are often leaking after 20 years of operation and urgently need to be replaced.I offer here Elkos manufacturer Nichicon, these are used in audio, hi-fi and musical instruments.The UQ series was specially developed for use in audio technology.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

Complet replacement set tactile switch for Sequential Prophet VSconsist of:1 pcs. orange button + 1 red LED1 pcs. blue button + 1 red LED8 pcs. black button + 1 red LED10 pcs. blue button31 pcs. black buttonOperational Life for all switch: 3.000.000 CyclesThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Slide Potentiometer 10 KOhm for  Data Entry Sequential Circuits Prophet VS RackThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Encoder 22 mm suitable forNord NordStage 2  - Main DialPractical advice:The encoders offered here come from the same manufacturer as those used by Nord. There are compared to the original small deviations in design:Pin distance here is 2.5 mm compared to 5 mm for the originalOriginal encoder does not have an "anti-rotation pin". This anti-rotation pin must be cut off at the new encoder.Mounting clip is not needed in many cases at Nord and can be removed. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.