Displays und LED

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forAKAI MPC-1000We offer an brand new display with LED technology for backlight. Display is ready mounted, no soldering is requiered.Display with white letters and black BacklightDisplay design upgrade:AKAI has built in a display with a yellow-green backlight that breaks out of the housing and disturbs the elegant appearance of this instrument. We offer a new display that matches the black case of the AKAI MPC-1000. The display fits harmoniously into the design of the sampler.Display defective?Our display is also suitable as a replacement part if the original LCD display is defective. It doesn't matter if only the backlight is no longer working or if the LCD is without function. Our display is perfectly suitable as a replacement display for the AKAI MPC-1000 sampler.Or are you looking for a Christmas present?Are you looking for a gift for an ambitious musician who works a lot with AKAI samplers or who has always been annoyed by the original display? How about a new display that visually enhances the device and also increases the value of the instrument.Unfortunately, we cannot offer the complete instrument, but only a new LCD display.The color of the shown display on picture, may differ from the original.Color: White Character  /  black BackgroundDelivery scope:Display is ready wired on delkiveryMounting parts if necessaryNotes on installation:The display is prepared by us ready wired and no soldering is required. All adjustments to the technical features of the MPC sampler are made by us on the display. Plug and Play installation. The new display is installed in exactly the same way as the old display was removed. For this reason, we do not provide installation instructions here. Nevertheless, we would like to point out that there is very little space in most devices. This work should only be done by technically experienced people.When switching on the new display for the first time, the optimum contrast point must be adjusted. This is achieved by pressing and holding the Stop key and turning the data wheel.  Installation service:We are also happy to install the display for you. Please ask.  

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forKorg Wavestation,Korg Wacestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument. Please let us now your instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people.We are proud to offer the thinnest displays available on the market. 

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg 01R/W Rack ModulDisplay for Korg 01/W Keyboard Version plese order hereWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope for LCD Display:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01/RW:The instrument must be disassembled almost completely to reach the display.The rack version of the Korg 01/RW synthesizer has much less mechanical effort than the keyboard versions.For the new display to work, one SMD resistor on the mainboard of the Korg 01/RW must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/RW have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Yamaha DX7 II OLED Display NEW whiteReady-to-plug prepared OLED display for replacement in Yamaha DX7 II. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Mechanical hints for the replacement of the OLED display in the Yamaha DX7II:Please consider in this case that the mechanical effort to get to the display in the instrument is quite high. Among other things, the keyboard and the mainboard must be disassembled. Everything is screwed. No soldering necessary.The display has a cover made of Plexiglass which is glued on the display and has to be transferred to the new display. We have had good experience with the following method: Insert fishing line or sturdy sewing yarn between the display and the cover and use a sawing motion to separate the adhesive.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 piece LED 3 mm Green The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. OLED Display New forSequential Circuits Prophet VSSequential Circuits Prophet VS RackSequential Circuits Studio 440To replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display. These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs blue LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtion Notes on installation:The instrument must be almost completely disassembled to access the display. Please do not underestimate the amount of work that is necessary. This work should only be carried out by people with technical, preferably electrotechnical, experience.The installation itself can be done without any soldering skills, but: We recommend to take out of function circuit part for the old backlight foil. For this, a transistor and a capacitor must be removed. This can also be done with a side cutter, i.e. without soldering. 

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu E4XTE-mu e6400We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in E-Mu e6400:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

1 pcs. Black LCD Display with LED Backlight replacementYamaha RM1xWe offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Black BackgroundDelivery scope of LCD Display for RM1x:Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha RM1x :To replace the display, the Yamaha RM1x is opened from the back. So the rear half of the case has to be removed. Afterwards the floppy drive, the DM board and a sheet metal frame must be unscrewed. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife. Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters. Note on contrast adjustment:It may be necessary to replace 2 SMD capacitors on the main board. Due to the ageing of the capacitors, the setting range for the contrast has shifted. 

1 pcs. OLED Display New forE-Mu Orbit V1E-Mu Orbit V2These different Display versions are available:BlueRed/OrangeYellowWhiteTechnical Hint for Mounting the OLED Display in E-Mu Orbit:The OLED display is supplied fully wired. The installation is possible without any problems. The display is screwed and the cable is only plugged in. Please make sure that the cable marking is plugged into pin 1 of the connector. Since the new OLED display has a lower height than the original LCD display, we supply washers and new screws to compensate for the height.Plug of Power cable. Don't work under Supply Voltage!!Lifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs.Clavia Nord LCD Display new white Replacement LCD Display for Claiva Nord Instruments. For installation soldering is requiered.Notes on installation for Nord LCD Display:This LCD Display is soldered to a PCB only with a small connector. This requieres very good soldering knowlege. Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 20,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.  

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Small soldering job to do.Color: White Character  /  Black BackgroundDelivery scope of Display Set:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Please let us know your Instrument, so we can put on right cable length onto your Display.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people. 

1 pcs. LCD Display brandnew in Yellow forKorg M1this is  a plug in ready Display replacement for Korg M1. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.Not compatible with M1r. This Display is a separate item.The color of the shown display, may differ from the original.These different Display versions are available:BlueblackWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

LCD Display with LED Backlight replacement including cable Kit forKawai K5000 We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionThis Display fits inNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, minor modifications to the electronics and the power supply are required. This work is to be done only by technically, best electrotechnically savvy people.  

Brand new OLED Display, blue, forKurzweil K1200 Pro 1Brand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1200 Pro 1 Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1200 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forYamaha QS-300We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Black BackgroundDelivery scope of LCD Display Replacement:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument. Please let us know your instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtion Notes on installation the Display in Yamaha QS-300:The instrument must be disassembled almost completely to reach the display.  This is a very time-consuming process. Please do not underestimate the disassembly and assembly effort.This work is to be done only by technically, best electrotechnically savvy people.No soldering required.All you need is a screwdriver and a side cutter. 

LCD Display with LED Backlight replacement including cable Kit forKorg 01R/WWe offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01R/W:The instrument must be disassembled almost completely to reach the display.The rack version of the Korg 01/RW synthesizer has much less mechanical effort than the keyboard versions.For the new display to work, one SMD resistor on the mainboard of the Korg 01/RW must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/RW have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people. 

1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forKurzweil PC3K6Kurzweil PC3K7Kurzweil PC3K8We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementNotes on installation The LCD Display in Kurzweil PC3XThe original Kurzweil display has different dimensions to today's commercially available displays. We have therefore developed an adapter board to adapt this. We supply the display pre-wired and pre-assembled.This work is to be done only by technically, best electrotechnically savvy people.The contrast of the display can be adjusted as usual using the control in the instrument.No soldering required.All you need is a screwdriver and a side cutter. 

1 pcs. new LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementPlease let us know your instrument. The cable must fit specifically to the instrument. Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people. 

1 piece LED 2 mm Green The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu E4KE-mu E-Synth We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes for installing the LCD display in the E-Synth:The display is prepared by us ready for plugging in. All adjustments to the technical specifications of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. We recommend removing this part of the circuit. In this case, an SMD transistor must be desoldered.We would nevertheless like to point out that there is very little space in most devices. This work should only be carried out by technically experienced individuals. Installation service for LCD Display:We are also happy to install the display for you. Please ask. 

1 pcs. OLED Display New forCasio CZ-1Casio CZ-101Casio CZ-1000Casio CZ-2000SCasio CZ-2600SCasio CZ-3000Casio CZ-5000The display has been prepared by us ready to plug in. We supply the display ready with the cable fitted for replacement in the synthesiser. All you need for this replacement is a screwdriver.Note on special characters: Casio uses special characters in the display of various instruments, e.g. note symbols. These symbols cannot be shown on the OLED display.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.