Products

1 pcs. JST PH Socket 2 pin for printed circuits These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Kawai Rotary Poti vertikal Real Time Control Electrical properties:The nominal resistance is 10 kOhm. The original potentiometer from Kawai has a resistance value of 20 kOhm. Since this potentiometer is used as a voltage divider, the resistance value is not decisive.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 10 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 piece Yamaha lower key strike felt for electric piano keyboardsThis felt is used by Yamaha in the 16NS keyboard, as found in the PSR-EW320, for example. This felt is located at the front of the keyboard.For easier installation, this felt is equipped with adhesive tape.The felt is designed for a 76-key keyboard. 

1x pc. Yamaha upper key strike felt for electric piano keyboardsThis felt is used by Yamaha in the 16NS keyboard, which is installed in the PSR-EW320, for example. This felt is located at the back of the keyboard. This is the felt on which all keys rest in their resting position.For easier installation, this felt is equipped with adhesive tape.The felt is designed for a 76-key keyboard. 

 1 pcs. MKP Film Capacitor 10 nF Safety 10mm X2 Safety film capacitor with the classification: X2 

1 piece Electrolytic Capacitor 220uF/35V for Switching Power Supply SmallManufakturer: NichiconHere i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Yamaha Contactrubber 14Y  There is a contact rubber for a normal, medium octave with 12 contacts. There is also a contact rubber for the top octave with 13 contacts.For a keyboard with 37 keys, you need:2 x 12 contacts1 x 13 contactsFor a keyboard with 61 keys, you need:5 x 12 contacts1 x 13 contacts 

1 pcs. Slidepotentiometer suitable for The Dynacord PowerMate mixing console series is now manufactured in a version 3. This potentiometer fits securely into the original version of the PowerMate series.Dynacord PM600Dynacord PM1000Dynacord PM1600The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Alfa Rpar AS662D SOIC16 replacement for Roland BA662The IC Alfa Rpar AS662D is a Dual Operational Transconductance Amplifier (OTA) with buffersthat was used in analogue synthesizers in the 1980s. Mechanical Description of AS662D:This AS662D is housed in a SOIC 16 package and is designed for surface mounting on a circuit board. The IC has 2 x 8 connecting pins with grid of 1.27 mm x 4.00 mm.Technical description of the AS662D:The AS662 consists of two independent OTAs, each with differential inputs and a push-pull output. Both amplifiers share a common power supply but operate independently of each other. Two buffers enable external control and offer flexibility in application.This AS662 can replace Roland BA662 and Texas Instruments LM13700.The BA662 was installed by Roland in the Jupiter series, the Juno series, the SH-101 and others, among others.Practical tips:These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Please be carefull because of static charing 

1 pcs. Alfa Rpar AS3109D VCF IC SOIC16 replacement for Roland IR3109The IC Alfa Rpar AS3109D is a voltage-controlled filter module that was used in analogue synthesizers in the 1980s. Mechanical Description of AS3109D :This AS3109D is housed in a SOIC 16 package and is designed for  surface mounting on a circuit board.The IC has 2 x 8 connecting pins with grid of 1.27 mm x 4.00 mm.Technical description of the AS3109D:Voltage-controlled four-pole filter. The four independent sections can be connected together to enable a variety of filter responses, including common filters such as low-pass, high-pass, band-pass and all-pass. A single input exponentially controls the frequency over greater than a 15 octave range with little control voltage feedthrough. AS3109 benefits from high input impedance buffers.Pin-compatible replacement for the IR3109 but different housing.Technically, the IC may differ slightly from the original. When replacing a Roland IR3109, the entire instrument must be recalibrated.The IR3109 was installed by Roland in the Jupiter series, the Juno series, the SH-101 and others, among others.Practical tips:These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Please be carefull because of static charing 

1 pcs. Quiettime GT-2 Relais  RY-5W-KQuiet Time GT-2 is a silentsystem for mechanical pianos. Manufacturer is Pianodisc.This relais is spare part for Pianodisc silentsystem Quiettime GT-2.

1 pcs. Alfa Rpar AS3360A VCA IC DIP14 replacement for Curtis CEM3360The IC Alfa Rpar AS3360A is a voltage-controlled amplifier module that was used in analogue synthesizers in the 1980s. The AS3360A is pin-compatible with the Curtis CEM3360 Mechanical Description of AS3360A :This AS3360A is housed in a DIP 14 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The IC has 2 x 7 connecting pins with grid of 2.54 mm x 7.62 mm. Difference between Standard and Advanced chip typ:AS3360A benefits from internal bandgap reference which improves stability of reference voltage and output current of VCA and improved level of attenuation of output current at zero control voltage. Technical description of the AS3360A:The AS3320 is a high performance voltage controlled four-pole filter with on-chip voltage controllable resonance IC. The four independent sections may be interconnected to provide a wide variety of filter responses, such as low pass, high pass, band pass and all pass. A single input exponentially controls the frequency over greater than a ten octave range with little control voltage feedthrough. Another input controls the resonance in a modified linear manner from zero to low distortion oscillation. For those demanding applications, provision has been made to allow trimming for improved control voltage rejection. Each filter section features a variable gain cell which is fully temperature compensated, exhibits a better signal-to-noise ratio and generates its low distortion predominantly in the second harmonic. The device includes a minus two volt regulator to ensure low power dissipation and consequent low warm-up drift.Technically, the IC may differ slightly from the original. When replacing a Curtis CEM3360, the entire instrument must be recalibrated.The CEM3360 was used in Oberheim and Sequential Circuits Synthesizern..Practical tips:These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Please be carefull because of static charing 

1 pcs. Alfa Rpar AS3340A VCO IC DIP16 replaecemt for Curtis CEM3340The IC Alfa Rpar AS3340A is a voltage-controlled oszillator module that was used in analogue synthesizers in the 1980s. Mechanical Description of AS3340A:This AS3340A is housed in a DIP 16 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The IC has 2 x 8 connecting pins with grid of 2.54 mm x 7.62 mm. Benefits of advanced chip typ:AS3340A are improved versions of AS3340. AS3340A and have much more output frequency stability against Vcc and VEE . Frequency stability can be improved If external reference voltage (with level approximately 1/3 Vcc) is connected to pin 9 (Soft Sync. Input). AS3340A benefits from improved symmetry of rising and falling edge of triangle signal (approx.. 50%).AS3345 benefits from additional Meander Output. Meander edge starts when Triangle changes it’s direction. These feature gives additional opportunities for design.Technical description of the AS3340A:The AS 3340 is a completely self contained, precision voltage controlled oscillator, featuring both exponential and linear control scales and up to four buffered output waveforms: triangle, sawtooth, square, and pulse with voltage controllable pulse width. Full temperature compensation makes these VCOs extremely stable, and eliminates the need for a temperature compensation resistor. The highly accurate exponential and linear control inputs are virtual ground summing nodes, allowing multiple control voltages to be mixed within the device itself.Practical tips:These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Please be carefull because of static charing 

1 pcs. Alfa Rpar AS3320 VCF IC DIP18 replacement for Curtis CEM3320The IC Alfa Rpar AS3320 is a voltage-controlled filter module that was used in analogue synthesizers in the 1980s. The AS3320 is pin-compatible with the Curtis CEM3320 Mechanical Description of AS3320 :This AS3320 is housed in a DIP 18 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The IC has 2 x 9 connecting pins with grid of 2.54 mm x 7.62 mm.Technical description of the AS3320 :The AS3320 is a high performance voltage controlled four-pole filter with on-chip voltage controllable resonance IC. The four independent sections may be interconnected to provide a wide variety of filter responses, such as low pass, high pass, band pass and all pass. A single input exponentially controls the frequency over greater than a ten octave range with little control voltage feedthrough. Another input controls the resonance in a modified linear manner from zero to low distortion oscillation. For those demanding applications, provision has been made to allow trimming for improved control voltage rejection. Each filter section features a variable gain cell which is fully temperature compensated, exhibits a better signal-to-noise ratio and generates its low distortion predominantly in the second harmonic. The device includes a minus two volt regulator to ensure low power dissipation and consequent low warm-up drift.Technically, the IC may differ slightly from the original. When replacing a Curtis CEM3320, the entire instrument must be recalibrated.The CEM3320 was used in Oberheim and Sequential Circuits Synthesizern..Practical tips:These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Please be carefull because of static charing 

1 pcs. Pianodisc Quiettime Phone Jack  1/8- 3.5 mm Stereo This phonejack is a stereo jack socket with 5 solder legs. In addition to the signal contacts for stereo signal transmission, this jack has 2 switching contacts.Furthermore, there are five plastic noses on the underside, which are intended as a guide and holding tiller. These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Electrolytical Capacitor 22uF/25V SMD The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Electrolytical Capacitor 470uF/16V SMD Manufakturer: NichiconThe capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Electrolytical Capacitor 22uF/16V SMDThe capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. FFC cable 14 pin 1,25 mm pitchFFC cable from Mainboard to LCD Both sides have the same connector  

This internal USB connection cable is specially designed for use with the Korg Pa5X. It enables a reliable connection between the USB port and the main circuit board and ensures stable data transfer within the instrument.Thanks to precisely fitting connectors, easy and secure installation is guaranteed.Features:Suitable for: Korg Pa5XType: Internal USB connection cableReliable signal and data transferHigh-quality workmanship for long-term use

1 pcs. Housing JST XH - 7 Pol Technical hint:These part is only housing without electrical contacts. For these contacts you will need a special Crimp tool.

1 pcs. new Korg RH-4L PCB Assy KeyboardRH-4, RH-4L or RH-4HL—one letter—big difference. Please note.this is set of three contact PCB as used in Korg RH-4L.This set contains LOW, MID ans HIGH contact PCB  - KLM 3587/88/89, 510d929735The circuit board is partially supplied with a blue protective film over the contacts. This protective film must be removed before installation. 

1 piece Electrolytic Capacitor 6.8uF/50V Würth ElectronicManufakturer: Würth Electronic The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs Yamaha CP4,CP40 GHD connection cable 7 pol for KeyboardThis Cable connects keysboard an Mainboard in your Instrument. Please note: This cable will most likely be available in many different lengths!!!!