Products

1 piece Elko 10,000uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Gold-Cap 1 F/5,5 V Manufakturer: Elna or Panasonic  

1 pcs. Technics ASUB Circuit Board QJBG2298 repairedTechnics SXPR-602Technics SXPR-603Technics SXPR-702Technics SXPR-703These circuit board was repaired by us and is tested  and fully working.important note - complex electronic errorFaults in the amplifier circuitry of these Technics electric pianos are very complex and require extensive electronics knowledge and professional experience.A new ASUB board is only part of the solution.We do not assume any warranty if a new ASUB board is inserted into a defective amplifier.

Mainboard for Technics E-PianosTechnics SXPX-222Technics SXPX-332These Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard. 

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg i2Korg i3We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play Display. No soldering is requiered.Color: White Character  /  Black BackgroundDelivery scope of Display Set:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation LCD Display:The instrument must be disassembled almost completely to reach the display.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Slider with 45mm Travel. Suitable for Yamaha Motif ES CS 1 - 4Yamaha Motif XS Volume 1 - 8The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

Replacement Keys for Yamaha NL4 AI KeyboardThese Keys fits for all Yamaha NL4 AI keyboards.Yamaha NL4 AI keyboard is used in:Yamaha Clavinova CLP-675Yamaha Clavinova CLP-775Yamaha Clavinova CLP-785Yamaha Clavinova CLP-795GP The Yamaha NL4 keyboard is a velocity-sensitive keyboard.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

1 pcs. LCD Display with LED Backlight replacement including cable Kit forKorg i2Korg i3We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  yellow BackgroundDelivery scope of LCD Display:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg i2,i3:The instrument must be disassembled almost completely to reach the display.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people.

1 pcs. Contact rubber for Kawai WK88 Keyboard discontinuedA contact rubber consists of 12 contacts and covers an octave.Contact high:  11 mmStrip bright:   25 mmStrip length:  164  mmNumber of contacts: 12These contactrubber for e-pianos has been used in:Kawai CA5Kawai CA7Kawai CA9Kawai MP8Kawai MP9500A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a 88 Key keyboard you will need 8 strips with 12 contacts. One strip can be cut after 4 contacts.

1 pcs. AD1862N - Digital-Analog-Converter for audio applicationResolution:                    20bitInterface:                      seriellNumber of DAC outputs: 2Number of channels:      1Case:                           DIP16 Mechanical Description of D/A Converter:The digital to analog converter is housed in a DIP 16 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The DA converter has 2 x 8 connecting pins with grid of 2.54 mm x 7.62 mm.Technical Description for AD1862N:The DA converter provides low distortion and typical differential linearity error is 0.001%. The interface is serial and provides a 20 bit resolution. No external components, such as temperature compensation or similar is required.It is a symmetrical supply voltage of +- 5V to +- 12V needed. 

1 pcs. brand new 10 inch extern LCD Display for Yamaha CVP seriesYamaha has been using color displays of various sizes in the Clavinova CVP models for many years. Displays are subject to natural aging, which leads to the fact that the displays are increasingly difficult to read. Even a readjustment of the contrast is no longer sufficient at some point. Yamaha has a very good spare parts supply for the Clavinova series. However, Yamaha cannot supply the original displays as replacements in all cases.We offer here an external HD LCD display that connects to the external video out of your Yamaha Clavinova CVP model. This ecternel Display shows same screen information as internal Display.The display resolution must be adjusted in many cases from 4:3 to 16:9 so the new display may be slightly blurred.Not an original spare part from Yamaha.Scope of delivery for extern Yamaha Clavinova LCD:1 pc. new LCD display, stand and cable for EU Attention: The color of the display shown may differ slightly from the original.  Notes on disposal:Each electronic component contains important raw materials that should be recycled. Please find out where in your area there is a corresponding collection point for these components. 

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forYamaha QY300We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope of LCD Display Replacmeent:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation the Display in Yamaha QY300:Inside Yamaha QY300 is very little space for the new display. A circuit board is mounted behind the display, it is called switch panel. On this switch panel a number of diodes are soldered which can collide with the new display. It is highly advisable to move these diodes to the back of the switch panel.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. Yamaha DC-IN PCB YA259 DiscontinuedThis DC-IN Circuit Board is used inYamaha P-155 For Europe only: 16VDC

1 pcs. Kawai Ring for Round KnobKawai ES-7Kawai MP-8Kawai MP-11 Technical Description of Kawai Knob:This ring for Round Knob is placed on the axis of the rotary potentiometer and pressed into the housing. The ring centers the axis of the rotary potentiometer in your Kawai Stage Piano.

Replacement Keys for Yamaha NL4SW KeyboardThese Keys fits for all Yamaha NL4SW keyboards.Yamaha NL4SW keyboard is used in:Yamaha CLP-745Note on the keys supplied:The keys are delivered without the black rubber that is mounted at the bottom of the key. The black rubber is taken from the old key. The rubber is clicked in and can be easily replaced. The Yamaha NL4SW keyboard is a velocity-sensitive keyboard. The keys have a wooden core that is covered with plastic.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used by  E-Mu Orbit Vs Phone Jack in FrontTechnical descriptionThe offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 piece Electrolytical Capacitor 33uF/400V for Switching Power SupplyManufakturer: Nichicon LowProfile Here i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. ""

1 piece Electrolytic Capacitor 220uF/35V for Switching Power SupplyManufakturer: NichiconHere i offer spezial Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. brand new OLED Display forTechnics PR-170Technics PR-270Technics PR-370Especially the electric pianos built under the Technics brand are very important to us. A long time ago the support by the manufacturer was completely stopped so that today no original spare parts are available. Even if Technics has produced in very good quality, some components can break. Partly this is simply due to the aging of the components. We offer here a brand new OLED display as a replacement for the originaly used LCD display.  Hints for mounting:To install this new OLED Display, the mechanical installation has to be done a different than the original display. The new OLED display will be delivered by us ready wired. No soldering work is necessary for this installation. Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instruction Notes on disposal:every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.  

1 piece Electrolytical Capacitor 680uF/450V for Switching Power SupplyManufakturer: EpcosHere i offer spezial Capacitor from manufakturer Epcos.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. brand new LCD Display with backlight suitable forYamaha CP4 Stage PianoYamaha CP40 Stage PianoWe offer here the original Yamaha spare part. Scope of delivery:1 pc. new LCD display, ready wired Notes on installation:Please be aware that you are opening an electrical device that is supplied with 230 volts. This work should only be carried out by people who have the appropriate expertise. Notes on disposal:Each electronic component contains important raw materials that should be recycled. Please find out where in your area there is a corresponding collection point for these components. 

1 pcs. Yamaha NU1X FU AC-IN BoardFor Europe only: 230VACUsed inYamaha CLP-675Yamaha NU1X

1 pcs yellow LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  Yellow BackgroundDelivery scope of Display set:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtion Notes on installation of LCD Display in Kurzweil K2000:The instrument must be almost completely disassembled to access the display. Please do not underestimate the amount of work that is necessary. This work should only be carried out by people with technical, preferably electrotechnical, experience.The installation itself can be done without any soldering skills, but: We recommend to take out of function circuit part for the old backlight foil. For this, a transistor and a capacitor must be removed. This can also be done with a side cutter, i.e. without soldering.