Products

1 pcs. Korg microKorg keyboard completemicroKorg XL

1 pcs. Yamaha switching Power Supply for HQ100SX DisklavierFrom our practical experience we know that this power supply unit, which is installed in the HQ100SX Disklavier from Yamaha, shows age-related defects. As a rule, this manifests itself in the complete failure of the power supply in this Yamaha Disklavier.Our Service:We can offer you the repair of this power supply unit. For the repair, it is sufficient if you have the power supply unit removed by a specialist electrical engineering company and send it to us. We will check and repair the power supply unit in our workshop.Safety notice:Switching power supplies store high voltages of approx. 300 volts DC over a long period of time. This spare part is only for specialists with appropriate knowledge of electrical engineering.  

1 pcs. Yamaha Tyros 5 Mainboard

1 piece Electrolytical Capacitor 2200uF/200V for Switching Power SupplyManufakturer: Cornell DubilierThe capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Knob for rotary potentiometers used inYamaha N1Yamaha N3Specifications:Diameter: 14,7 mmHight:   17.2 mmShaft:   6 mm, flattedPraktical tip:The knobs are just plugged on. No tools are needed.

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu DarwinWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

1 pcs. Contactrubber GH 2M suitable forYamaha CP1

1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVE-mu e64We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: blue Character  /  white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping is eliminated)lifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. In this case it must be desoldered.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people. Installation service:We are also happy to install the display for you. Please ask.

1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVE-mu e64We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  /  yellow BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping is eliminated)lifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. In this case one part must be desoldered.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people. Installation service:We are also happy to install the display for you. Please ask.

LCD Display with LED Backlight replacement including cable Kit forYamaha TG77We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  yellow BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:Inside Yamaha TG 77 is very little space for the new display. A circuit board is mounted behind the display, it is called switch panel. On this switch panel a number of diodes are soldered which can collide with the new display. It is highly advisable to move these diodes to the back of the switch panel.This work is to be done only by technically, best electrotechnically savvy people.

1 pcs. Xvive MN3005 4096 Stage BBD PDIP14(C)Rebuild of the MN3005 BBD from Panasonic. We think that it is a 1:1 clone from original Panasonic Chip. FeaturesVariable delay time from 20.48ms to 204.8msWide dynamic range 75dB (typ)Total harmonic distortion <0.5%Clock frequency from 10Hz up to 100KHzPackage: Special DIP-14 Mechanical Description:The IC is housed in a special DIP 14 package and is designed for trughhole mounting on a circuit board. THis chip is pin compatible to Panasonic MN3005 .ICs are sensitive to static charge! Handle with care.Semiconductors are excluded from exchange. 

1 pcs. Contactrubber 16N 1M suitable for Yamaha This keyboard is used in these modells:Yamaha PSR-e203These Contactrubber was buildt in two different colors. Function is in both cases the same.

1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu e5000 UltraWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  /  white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

1 pcs. Music stand for Technics E-Pianos suitable forTechnics PX-222This Music stand is made of wood and is pluggableHole Distance: 473 mmAdvice:The music stand is used and has signs of wear due to its age, e.g. damage to the varnish.

1 pcs. 6 pin FFC socket with 2.54 mm pitch6 pinPitch: 2.54 mmLength:  17 mmdeepth:    4,50 mmhight:       6,70 mmThese socket is used in Korg Poly 61 between KLM-475 and KLM-476Technical description

1 pcs yellow-green LCD Display with LED Backlight replacement including cable Kit forKawai K5Kawai K5mWe offer an absolutely equivalent display using modern LED technology for backlight.Color: black Character  /  yellow-green BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation the Display in Kawai K5:The instrument must be disassembled almost completely to reach the display. Furthermore, minor modifications to the electronics and the power supply are required. This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs white LCD Display with LED Backlight replacement including cable Kit forKawai K5Kawai K5mWe offer an absolutely equivalent display using modern LED technology for backlight.Color: black Character  /  white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, minor modifications to the electronics and the power supply are required. This work is to be done only by technically, best electrotechnically savvy people.  

Recapping set for Technics SX-PX1 E-PianoThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Technics PX-1 is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for complete Technics SX-PX1 E-Piano. The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Mainboard for Yamaha CVP-207 E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard. 

1 pcs. Mainboard for Yamaha CVP-209 E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard. 

1 pcs. Replacement stereo rotary potentiometer suitable for volume control inKorg Volca Sample 2Electrical properties:The stereo nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The six solder pins are 0,6 mm wide (one of them) and they are arranged in two rows in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. LCD Display forKorg Krome

JST MQ socket 9 pin for printed circuitthis MQ Socket form JST is used by Technics E-Pianos for connecting Printid Circuit Boards.Pitch: 2.0 mmThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pc. Contact rubber for Roland PA4 keyboard -- discontinued  --Features:    Height of contacts: 9 mm    width of the strip:    32 mm    Length of the strip: 165 mm    Number of contacts per strip: 12 contactsRoland spare part number: 22185247This contactrubber fits in Roland PA4 and also Roland PA4A Keyboard.One contact strip consists of 12 contacts and thus covers one octave. For a complete replacement of the contact strips in a keyboard with 88 keys, 7 contact strips + 4 contacts are needed. The remaining 4 contacts can easily be separated from a contact strip with 12 contacts. For this purpose, a notch is provided in the contact strip after every 4 contacts.