Products

1 pcs. Korg N1 Volume Slide PotentiometerKorg N1Korg N264Korg N364OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Replacement rotary potentiometer suitable forQuasimidiElectrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 12 mm, the total length without pins is 25 mm. In this total length the casing is 9 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is slotted and Knurled on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 12,2 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Yamaha Power cable 2 pol for EU, 2.5mYamaha genuine part

1 pcs. Service Kit Kawai RG88B PWB Assy KKB-015This service kit replaces the circuit boards and contact rubbers in the Kawai RG88B keyboard. Only possible as a replacement for keyboards in which contact rubbers with two contacts per tone were used.This set of boards replaces the board KKB-015 The set consists of two boards, fully equipped with new contact rubbers.Compared to the original circuit boards, Kawai has extended the lifespan and refined the dynamic range.It is only possible to exchange this sentence completely. Mixing old boards or contact rubbers with new boards or contact rubbers leads to a malfunction.These Board fit in these e-pianos:Kawai KDP-80Kawai KDP-90Kawai ES100Kawai CN31Kawai CN32Kawai CL-15

1 piece Elko 1,000uF/35V for Switching Power SupplyManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Yamaha NL4 Guide CapThis rubber fits in these keyboardsYamaha NL4This rubber sits at the head of the key guides and is used for the black deeds and for the white deeds.Color: black

1 pcs. COIL ASS'Y (AL) L=75 BL SX100/RSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Roland PG-1000 OLED Display Blue NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Roland PG-1000 OLED Display white NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Yamaha MA80S PSU BoardFor Europe only: 230VACUsed inYamaha CVP-303 

1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Clavia Nord 4 way Power Supply IEC14 V1.3  brand new replacement power supply for many Clavia Nord models.Please pay attention to the mains connection: This power supply has a 3-pin IEC C14 connector. Older Clavia Nord models use a 2-pin Euro connector. Secondary side: 10-pole ribbon cableThis Power supply deliver:+ 3.3 Volt+5 Volt+/-12 VoltSafety note: Here you are working directly on the mains voltage of 230 VAC. This work is only suitable for people with appropriate electrical knowledge. 

1 pcs.  Yamaha FFC cable for GHL KeyboardKeyboard connection cableThis cable connects Yamaha GHL Keyboard with Mainboard   

1 pcs. Kawai Pedal screw longDimensions: M8 x 25 mm Note: 

1 pcs. Roland JP8000 OLED Display brandnew in white this is  a plug in ready OLED Display replacement for Roland JP8000 Synthsizer. For this display replacement, we strongly recommend shortening the mounting bolts in the housing of the Roland JP8000. The OLED display itself is supplied pre-wired. No soldering is required Mounting instructions for Roland JP8000 OLED:The mechanical assembly of this OLED display is somewhat more complex. The synthesiser is opened from the back and almost all components have to be removed to access the display, unfortunately the keyboard also has to be removed.The display assembly in Roland JP-8000:We have developed a special cable adapter for the display in the Roland JP8000. This makes it possible to continue using the flat cable used in the original. The flat cable is simply plugged in.The display in the Roland JP8000 is mounted on plastic bolts that are firmly connected to the display frame of the synthesiser, but these plastic bolts are much too high for the new OLED display at 8 mm. It is best to shorten these bolts to 5 mm so that the new OLED display comes very close to the windscreen. These plastic bolts can be easily sawn off with a small modelling handsaw. In our picture it is a saw from Tamiya.The big advantage is that a shim can be placed underneath as a height stop. This allows me to saw off the correct height very safely.Scope of delivery Roland JP8000 OLED Display:OLED display ready wiredInstallation instructionsmounting materialThe color of the shown display, may differ from the original.Installation service for Roland JP8000:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs.Yamaha USB Socket Typ B with frame  PCB used by: These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 pcs. Korg M1 OLED Display brandnew in yellow this is  a plug in ready OLED Display replacement for Korg M1 Keyboard Synthsizer. For this display replacement, we strongly recommend shortening the mounting bolts in the housing of the Korg M1. The OLED display itself is supplied pre-wired. No soldering is requiredNot compatible with Korg M1R Rack Synthesizer. This Display is a separate item.Mounting instructions for Korg M1 OLED:The mechanical assembly of this OLED display is somewhat more complex. The synthesiser is opened from the back and almost all components have to be removed to access the display, unfortunately the keyboard also has to be removed.The display assembly: The display in the Korg M1 is mounted on plastic bolts that are firmly connected to the display frame of the synthesiser, but these plastic bolts are much too high for the new OLED display at 10 mm. It is best to shorten these bolts to 5 mm so that the new OLED display comes very close to the windscreen. These plastic bolts can be easily sawn off with a small modelling handsaw. In our picture it is a saw from Tamiya.The big advantage is that a shim can be placed underneath as a height stop. This allows me to saw off the correct height very safely.Scope of delivery Korg M1 OLED Display:OLED display ready wiredInstallation instructionsmounting materialThe color of the shown display, may differ from the original.Installation service for Korg M1 Keyboard:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. TRANSISTOR 2SC1403Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. TRANSISTOR 2SD381Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. TRANSISTOR 2SA912Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. FET 2SK146Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. IC YM2154 RX-15Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. POTENTIOMETER (SLIDE TYPE) A2MSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. TOP CAP ASSEMBLY GY (U) 02RSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.