Products

Spare parts for Roland PA4 Keyboard Does a key on your electric piano hang or clack loudly when you play it? In these cases, it is usually not the key that is defective but the underlying hammer that is broken.This part fits for all Roland PA4 KeyboardsRoland PA4 Keyboard is used inRoland HP-237eRoland HP-555GRoland HP-7700Roland KR-370Roland KR-375Roland KR-570 und KR-575Roland KR-770Roland KR-1070Roland KR-4300Roland RD-500The S-Key fits in Keyboard PA4 AND PA4APlease have a look at the video for replacing Hammers.

1 pcs. Slider with 45mm Travel. Suitable for Kurzweil PC88The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 piece Electrolytical Capacitor 6800uF/25V for Audio circuitsManufakturer: NichiconSeries: LKS - Snap InHere i offer spezial Capacitor from manufakturer Nichicon. The series LKS is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. OLED Display New forE-Mu Proteus 1E-Mu Proteus 2E-Mu Proteus 3To replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. brand new LCD Display with backlight suitable for  - Discontinued -Yamaha Disklavier MX100IIYamaha Disklavier HQ100SXThe LCD displays installed by Yamaha in the MX100, HQ100 or MX100II and HQ100SX disklavier series are now getting on in years. The original displays are very difficult to read in many disklaviers or the LCD displays are completely defective.We offer here the original Yamaha spare part. Scope of delivery:1 pc. new LCD display, ready wired Notes on installation:Please be aware that you are opening an electrical device that is supplied with 230 volts. This work should only be carried out by people who have the appropriate expertise. Notes on disposal:Each electronic component contains important raw materials that should be recycled. Please find out where in your area there is a corresponding collection point for these components. 

Brand new OLED Display, yellow, forKurzweil K1200 Pro 1Brand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1200 Pro 1 Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1200 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 00Roland D-70, mainboard version 01We offer here a high quality replacement display with modern LED technology for the backlight.Color: white font/blue backgroundScope of delivery:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description!Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", or "02". 

1 pcs. LCD Display brandnew in Yellow forKorg M1Rthis is  a plug in ready Display replacement for Korg M1R . You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired. The color of the shown display, may differ from the original.These different Display versions are available:BlueblackWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. white LCD Display with LED Backlight replacement including cable Kit forAKAI MPC-1000We offer an brand new display with LED technology for backlight. Display is ready mounted, no soldering is requiered.Display with black letters and white backlightDisplay design upgrade:AKAI has built in a display with a yellow-green backlight that breaks out of the housing and disturbs the elegant appearance of this instrument. We offer a new display that matches the black case of the AKAI MPC-1000. The display fits harmoniously into the design of the sampler.Display defective?Our display is also suitable as a replacement part if the original LCD display is defective. It doesn't matter if only the backlight is no longer working or if the LCD is without function. Our display is perfectly suitable as a replacement display for the AKAI MPC-1000 sampler.Or are you looking for a Christmas present?Are you looking for a gift for an ambitious musician who works a lot with AKAI samplers or who has always been annoyed by the original display? How about a new display that visually enhances the device and also increases the value of the instrument.The color of the shown display on picture, may differ from the original.Color: Black Character  /  white BackgroundDelivery scope:Display is ready wired on delkiveryMounting parts if necessaryNotes on installation:The display is prepared by us ready wired and no soldering is required. All adjustments to the technical features of the MPC sampler are made by us on the display. Plug and Play installation. The new display is installed in exactly the same way as the old display was removed. For this reason, we do not provide installation instructions here. Nevertheless, we would like to point out that there is very little space in most devices. This work should only be done by technically experienced people.When switching on the new display for the first time, the optimum contrast point must be adjusted. This is achieved by pressing and holding the stop key and turning the data wheel.  Installation service:We are also happy to install the display for you. Please ask. 

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu DarwinWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

1 pcs. Service Kit Kawai RH88B PWB Assy KKB-044(1)This service kit replaces the circuit boards and contact rubbers in the Kawai RH88B keyboard. Only possible as a replacement for keyboards in which contact rubbers with three contacts per tone were used.This set of boards replaces the board KKB-040. The set consists of two boards, fully equipped with new contact rubbers.Compared to the original circuit boards, Kawai has extended the lifespan and refined the dynamic range.It is only possible to exchange this sentence completely. Mixing old boards or contact rubbers with new boards or contact rubbers leads to a malfunction.These Board fit in these e-pianos:Kawai CN17Kawai KDP110Kawai KDP120Kawai ES520Caution during disassembly: The operation LED on the front of the piano is plugged into the sensor board.

1 pcs. Rotary Potentiometer C characteristicSubstitute rotary potentiometer forYamaha CP5Electrical properties:C characteristicThe nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs Kawai Power Switch Board KEP-416   -- Discontinued --this PCB fits inKawai ES7Kawai ES8Mechanical Description: Practical advice:Plug of the device. Don't work under Voltage. 

1 pcs. Yamaha contact PCB for Yamaha GHL KeyboardThis keyboard is used inYamaha P-115Yamaha P-125Yamaha YDP-S30Yamaha YDP-143

 1 pcs. Cap round 12 mm for tact switchThis cap for stylus has a diameter of 12 mm and a receptacle of 3 x 3 mm.Suitable as a spare part for E-Mu sampler

1 pcs tactile switch 7,3 mm for YamahaThese tact switch are soldered onto a circuit board. Manual skills and experience in soldering are required to replace the tact switch.why should I solder new pushbutton

1 pcs yellow LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  white BackgroundDelivery scope of Display set:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtion Notes on installation of LCD Display in Kurzweil K2000:The instrument must be almost completely disassembled to access the display. Please do not underestimate the amount of work that is necessary. This work should only be carried out by people with technical, preferably electrotechnical, experience.The installation itself can be done without any soldering skills, but: We recommend to take out of function circuit part for the old backlight foil. For this, a transistor and a capacitor must be removed. This can also be done with a side cutter, i.e. without soldering. 

1 pcs. Rotary Potentiometer vertikal 9 mm with center click, 10kOhmSubstitute rotary potentiometer for RoThe rotary pot fits also inKorg KorgElectrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 10 x 12 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of gray plastic. Its head ends in corner radius. The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 11 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. new Brand new OLED Display forKurzweil K1000 AX PlusKurzweil K1000 HXKurzweil K1000 PXKurzweil K1000 SXBrand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1000  Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1000 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

1 pcs. Encoder 16 mm wide with Detends suitable forWaldorf Microwave 2The Waldorf Microwave II has one of these encoder with detents. These encoder is mounted beside the display.Practical advice:The axis of this encoder is 2 mm longer than the axis of the original encoder of the Waldorf Microwave 2. Under circumstances the axis must be shortened. Since the axis of the encoder is made of plastic, shortening is quite easy.These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. LCD display with LED backlightsuitable forRoland W-30We offer here a high quality replacement display with modern LED technology for the backlight.Mounting of LCD Display is plug and play. No soldering is required.Color: black font/white backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable ready to plug in. Roland used in W30 a very special connector. We rebuild theses connector with handcraft pincompatible to the original one. Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland W30:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation. For this you have to cut two small componnents. No soldering is required.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 02Roland D-70, mainboard version 03We offer here a high quality replacement display with modern LED technology for the backlight.Color: white font/black backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description! Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland D-70:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", "02" or "03". 

1 pcs. Korg T1 Volume Slide PotentiometerKorg T1Korg T2Korg T3OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Korg Wavestation Volume Slide PotentiometerOEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.