Products

1 pcs. tactile switch suitable for modelsNord ComboNord ElectroNord LeadNord ModularNord PianoNord StageThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece Electrolytical Capacitor 100uF/35V for Audio circuitsManufakturer: NichiconSeries: FWHere i offer spezial Capacitor from manufakturer Nichicon. The series FW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Electrolytical Capacitor 4.7uF/50V for Audio circuitsManufakturer: NichiconSeries: FWHere i offer spezial Capacitor from manufakturer Nichicon. The series FW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

1 pcs. Rotary Potentiometer vertikal 11x11 mm. 10kOhmSubstitute rotary potentiometer forKorg Kronos     -   MIX SectionRoland MC-909Yamaha RS-7000   - without Center Click The here shown substitute fits also inKorg M3Korg electribe EMX1Korg electribe ESX1Korg Oasys EqualizerKorg Triton lehere the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. Volume Slide potentiometer with 30mm travel. Suitable for Yamaha DX7Yamaha DX9Yamaha DX11Yamaha DX21Yamaha DX27Yamaha DX100 This volume control with the labelling EWA-NFOC is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

Power cabel 2m with 2P plug for Roland InstrumentsVDE testedCable: H05VV-F2G0,75mm²Socket: C10Mains plug CEE 7/7 earth contactLength: 2 mAlso forKorgAkai 

1 pcs. tactile switch suitable for modelsKorg MonopolyKorg PolySixKorg BX3/CX3      first Version build in 1980'sRoland JX 10PRoland Jupiter 8Roland TR808Part Number: Korg: 37503400, Roland: 13169601The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece Electrolytical Capacitor 10uF/63V for Audio circuits  - discontinued -Manufakturer: NichiconSeries: FWHere i offer spezial Capacitor from manufakturer Nichicon. The series FW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece bipolar Elko 22uF/25V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Xvive MN3007 1024 Stage BBD DIP8  -  Panasonic MN3007 cloneRebuild of the MN3007 BBD from Panasonic. We think that it is a 1:1 clone from original Panasonic Chip. Features of MN3007Variable delay time from 5.12ms to 51.2msWide dynamic range 80dB (typ)Total harmonic distortion <0.5%Clock frequency from 10Hz to 100KHz Package: DIP-8 Mechanical Description of MN3007:The IC is housed in a DIP 8 package and is designed for trughhole mounting on a circuit board. THis chip is pin compatible to Panasonic MN3007.ICs are sensitive to static charge! Handle with care. Semiconductors are excluded from exchange.   

1 pcs tactile switch suitableYamaha RM1XYamaha MX100II disklavierThese switch is for Keyboard ButtonsYamaha Part Number: VS1809800The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece LED 3 mm Blue This LED is a technical equivalent to the orignial Korg LED's.The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Contact rubber for Kawai KeyboardFeatures:Height of contacts: 11 mmWidth of the strip: 25 mmLength of the strip: 164 mmNumber of contacts per strip: 12Note on replacing the RH88A contact rubbers:Please always replace all contact rubbers in the keyboard.A new contact rubber has better playing dynamics than a contact rubber that is 8 or 10 years old. If you replace only one contact rubber, you will notice differences in the playing dynamics.A contact rubber consists of 12 contacts and covers an octave. A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a 88 Key keyboard you will need 8 strips with 12 contacts. One strip can be cut after 4 contacts.

1 pcs. Yamaha GH3 Actuate RubberThis rubber fits in these keyboardsYamaha GHDYamaha GH3Yamaha NL2This rubber is used on every single key as stopperColor: black 

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland D-70    - C1, BrightnessRoland JD-800  - Lever shorten!!!Roland PG-300Roland PG-800This Fader with the labelling EWANFX15B15 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Attention:Special pin layout. This potentiometer has a special pin layout and can only be used as a replacement for EWANFE or EWANFJ potenziometers. Not suitable for EWANA potentiometers.Without center. This potentiometer is only available without center.Electrical properties:The nominal resistance has 100 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The potetniometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Clavia Nord Volume Dreh Potentiometer Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 16 mm Diameter, the total length without pins is 32 mm. In this total length the casing is 9 mm long. On this casing is the thread with 7 mm length connected and out of the thread the axis rises with 15 mm length. The axis has a diameter of 4 mm and is flattened on a length of 12 mm. It is made of metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The three solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. Fatar Keyboard tripple Contact rubber 13P new  technichal dimensionsNo of contacts: 13Width: 22.7 mmheigh: 6.5 mmColor: white or grey 

1 pcs. tactile switch suitable for models Korgis40, is50Pa1 XPro, Pa2 XProPa50                        without LCD BoardPa60, Pa80, Pa500, Pa800SP200Korg Part Number:  INT0001008The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 piece bipolar Elko 47uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece bipolar Elko 22uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer spezial bipolar Elkos from manufakturer Nichicon. The series Muse ES is developt spezial for use in audio signals path.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Kawai Holder Score StandThis housing is made of plastic1 pc. The price is for one holder.This score stand is used onKawai ES7Kawai ES8Kawai MP7Kawai MP10Kawai MP11Kawai VPC1

1 pcs. Nut and Washer VA M9 x 0,75 mm for SW12Technical descriptionThis nut fits to some Phone Jacks . The nut is build from stainless steal and has Metric fine thread M9 x 0.75 mm. The thickness is 2 mm and wrench size is 12 mm. 

Rotary Potentiometer vertikal 11x11 mm with center click, 10kOhmSubstitute rotary potentiometer for Roland MC-909The rotary pot fits also inKorg electribe EMX1 Korg electribe ESX1here the axis sticks out 2,5 mm.Electrical properties:The nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient runs linear. Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 piece Korg LS-88 Keyboard spring KOC-C50231