Products

1 pcs tactile switch suitable for E-Mu e4K              all exept   Rec,Play,Stop,RW,FWE-Mu E-Synth       all exept   Rec,Play,Stop,RW,FWE-Mu E4-XTE-Mu e6400Launch PadThis is exactly the same switch used by E-Mu on manufacturing. On this switch i am not satisfied with life span.why should I solder new pushbutton

1 pcs. Yamaha Pedalcable No3This cable with plug is used by Yamaha for different E-Piano Modells. This Cable fits for Pedal with 3 Pedals.This cabel is for 6 Pol Mini Din Plug. All 6 wires are assigned on both sides.This cable is used in:Yamaha CLP-745Yamaha CLP-810SYamaha CLP-840Yamaha CLP-860Yamaha CLP-990Old Manufacturer Number: V0044700

1 piece Elko 100uF/35V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece Elko 220uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Screw 6 mm Black PhillipsLength: 6 mm Material: Iron blackThis Screw is used in many Clavia Nord instrumnets as Housing screw. This one can be located on rear side or on bottom.

1 piece Electrolytical Capacitor 47uF/25V for Audio circuitsManufakturer: NichiconSeries: FWHere i offer spezial Capacitor from manufakturer Nichicon. The series FW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

1 piece Electrolytical Capacitor 0.47uF/50V for Audio circuitsManufakturer: NichiconSeries: FWHere i offer spezial Capacitor from manufakturer Nichicon. The series FW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Screw 16 mm Black PhillipsLength: 16 mm Material: Iron blackThis Screw is used in many Clavia Nord instrumnets as Housing screw. This one is used for red side panels.

1 pcs. IC Socket for D5534ATechnical Hint:The IC socket has 17 legs with a grid of 2 mm. The IC D5534A has 16 legs + an empty position as a built-in marker. I think it makes sense to take over this empty position for the IC socket as well. The corresponding soldering pin can be easily pushed out.Mounting of this part requiers soldering. 

1 pcs. Yamaha Reface MIDI cable forYamaha Reface CPYamaha Reface CSYamaha Reface DXYamaha Reface YCthis is a special MIDI cable for Yamaha Reface CP Synthesizer. Because of small housing Yamaha used here a MINI DIN plug.Adapter cable: The cable is provided with a MINI DIN plug on the side to the synthesizer from which the two usual 5-pin DIN sockets are then led out. 

1 pcs. Quasimidi LED-tactile switch suitable for modelLED colour: Red We offer here switch from the second redesigned series where LED body is clear.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Tactile switch suitable forSequential Circuits Prophet VSThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

LED-tactile switch suitable for modelRoland TR-909LED colour: RedRoland replacement part no.: 13169627The construction part is not longer built. The old serial number was KHJ-11901. With that serial number the part was built during the 80s.We offer here switch from the second redesigned series where LED body is clear.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs.Clavia Nord OLED Display new white this is  a plug in ready Display replacement for Claiva Nord Instruments. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation for Nord OLED Display:Here we deliver an OLED display without mounting frame. This mounting frame must be taken from the original display. The OLED display is glued into the frame with adhesive tape. The display can be slowly removed from the frame with a constant pull. Afterwards, please transfer the adhesive tape to the new OLED display. Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.  

Phone Jack 1/4- 6.3 mm, Stereo with switch, for printed circuit used in  Korg, Roland or Yamaha InstrumentsThis part is used inKorg OasysRoland Juno GYamaha Tyros 2 Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Tactile switch suitable for  The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.Why should I solder new pushbutton

1 pcs. slide potentiometer with 30mm travel. Suitable Slider forVolume Control forKorg C150, C350, C3200, C6500Korg ix300, I5SKorg KarmaKorg M50 Master VolumeKorg Oasys 76, Oasys 88Korg Triton EX61, EX76, EX88Korg Triton LE61, LE76, LE88Korg Triton, Triton extremeKorg Triton Pro76, Triton ProXKorg TR76, TR88Korg X50 This volume control with the labelling EWANA0C10B14 is no longer available from the manufacturer Panasonic, because it is no longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.  Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position.The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 piece Electrolytical Capacitor 0.1uF/50V for Audio circuitsManufakturer: NichiconSeries: FWHere i offer spezial Capacitor from manufakturer Nichicon. The series FW is developt spezial for use in audio circuits.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

Electrolytical Capacitor Bipolar 10uF/16V SMD Manufakturer: Nichicon The capacitors are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required

1 piece Elko 470uF/35V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

1 pcs. new Contactrubber for Yamaha 16NW KeyboardThis keyboard is used in these modells:Yamaha MOX6Yamaha Tyros 1Color of these Contactrubber may be different.

1 pcs. tactile switch suitable for modelsRoland MC-505Roland MC-808Roland MC-909Roland Part Number:  1343478The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Contact rubber for Kawai KeyboardA contact rubber consists of 12 contacts and covers an octave.Contact high:  11 mmStrip bright:   25 mmStrip length:  164  mmNumber of contacts: 12A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a 88 Key keyboard you will need 8 strips with 12 contacts. One strip can be cut after 4 contacts.

 1 pcs. PP Capacitor 22 nF Safety