1 pcs. Power cabel with 3Pol C13-plug VDE testedCable: H05VV-G3G0,75mm²Length: 1,8 m

AC Power Inlet with AMP Connectortechnical Dates:Termination AMP Socket 4,3 mm  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with AMP Sockets.The electrical load is 10 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.

Replacement Keys for Korg X50 KeyboardKEY ASSY 13(M) KOC-H30306-1Color: white mechanical construction: This Keys are only available as complete set for one Octave. There is one part for a middle Octave, one part for the first and one part for the last Octave.

Replacement Keys for RH4 KeyboardRH4 keyboard is used in Korg SP-170Korg SP-280Krome 88 Color: whiteThe RealHammer 4 keyboard (RH4) is a touch-sensitive keyboard with 4-zone hammer mechanics.The unweighted keys have a length of 22.8 cm with a width of 2.24 cm. The depth of the key is 4.5 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is formed downside the key. The Contactor is 11 cm from the front. At the back end, the keys are connected with other keys over a bridge. These keys are only available as complete set for a Octave.4-Zone Hammer Mechanics:A 4-zone hammer mechanism is now state of the art for high-quality e-piano keyboards. By means of the four different zones the keyboard manufacturers try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are four different hammers with different weight. mechanical construction:Particular mention should be made of the structure of the hammers. The hammers used here are made of a continuous metal part, which should guarantee a long life for these hammers. Only the attached plastic parts appear quite graceful. This Keys are only available as complete set for one Octave. There is one part for a middle Octave, one part for the first and one part for the last Octave.

1 pcs. Slider with 45mm Travel. Suitable for Korg TriniityThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs.  6 pin FFC cable with 2.54 mm pitch and 100 mm length6 pinPitch: 2.54 mmLength: 100 mmcontactlength: 7 mmcontacts same sideThese cable is used in Korg Poly 61 between KLM-475 and KLM-476Technical description

Recapping Set for Korg DW8000The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Korg DW8000  series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.If no longer available from Nichicon, we use Würth or Rubycon Capacitors.This Recapping Set contains all necessary Capacitors for Korg DW-8000 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. LCD Display brandnew in blue forKorg M1Rthis is  a plug in ready Display replacement for Korg M1R . You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired. The color of the shown display, may differ from the original.These different Display versions are available:BlueblackWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. new LCD Display with LED Backlight replacement including cable Kit forKorg i2Korg i3We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play Display. No soldering is requiered.Color: Black Character  /  White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people. 

1 pcs. LCD Display with LED Backlight replacement including cable Kit forKorg Wavestation,Korg Wacestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  yellow BackgroundDelivery scope of LCD Display:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg Wavestation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people.

1 pcs. new Korg LS88 PCB Assy KeyboardThis keyboard is used inKorg Kronos 2 LS88this is set of three contact PCB as used in Korg Kronos 2 LS88.This set contains LOW, MID ans HIGH contact PCB.This Set is KLM-3543, KLM-3544, KLM-3545. 

1 pcs. Korg 01/W Data Entry SliderKorg 01/WKorg 01/W FDKorg 01/W ProKorg 01/W ProXOEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. CCFL neon lamp 100 x 2,2 mm with cape  for LCD Display BacklightYamaha PSR-S700Yamaha PSR-S900Safety advice to CCFL tubes:These neon tubes are very sensitive. Handling and mounting must be done very very carefully.The fluorescent tubes are operated with a high voltage of approx. 180V AC. Please observe the corresponding safety regulations of the VDE. 

Korg Prophecy Recapping Set for switching power suplly unitWarning: Switching power supplies store high amounts of energy for long periods of time. You are working on assemblies that operate at 230 V AC and approx. 300 V DC.You are carrying out this work at your own risk and under your own responsibility.The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.Our recapping set consists of capacitors from renowned manufacturers. Preferably from Nichicon, Würth or Vishay. The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Korg SV-1 Tube 12AX7  

Replacement keys, weighted for Fatar TP/8+ KeyboardFatar TP/8+ keyboard is a touch sensitive keyboard with weighted keys.Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points. The weighted keys have a length of 19,5 cm and a width of 2.24 cm. The thickness of the keys is 1,2 cm. Key guidance and upper stop point are implemented in this keyboard through an eye at the key bottom. The contactor, which presses the contact rubber strip is  worked out by an increase of 10,5 mm. The distance from the front side of the key is 13 cm. At the end of the key is a semi-circular passage aperture into which a spring is hooked. The keys are in color cream white.

1 pcs. tactile switch suitable for modelsKorg Oasys      (Pad Velocity - only one switch needed) The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. 230V Switching Power Supply for Korg M1, reconditionedKLM-1269 This Power Supply Board is fully reconditioned, like new. 230V Version

LCD Display forKorg Triton Studio

1 pcs. LCD Display with LED Backlight replacement including cable Kit forKorg T1Korg T2Korg T3We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  yellow BackgroundDelivery scope of LCD Display set:Display ready wiredMounting partsInstruction for replacementPlease let us know your instrument on order.The cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg T1,T2,T3:The instrument must be disassembled almost completely to reach the display.Small soldering job: For the new display a jumper has to be soldered on the audio board.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people.

Single Button 17 x 7 mm (No Window)Korg Pa1XKorg Pa1X ProKorg Pa2XKorg Pa2X ProKorg Pa800Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

Single Button 19 x 7 mm (No Window)Korg Pa1XKorg Pa1X ProKorg Pa2XKorg Pa2X ProKorg Pa800Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

Single Button 19 x 7 mm with WindowKorg Pa1XKorg Pa1X ProKorg Pa2XKorg Pa2X ProKorg Pa800Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

Single Button RED 19 x 7 mm with WindowKorg Pa1XKorg Pa1X ProKorg Pa2XKorg Pa2X ProKorg Pa800Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future. No longer suitable!!!! Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.