Yamaha

1 pcs. Yamaha DX5 OLED Display NEW whiteReady-to-plug prepared OLED display for replacement in Yamaha DX5. The new OLED display is supplied by us with a new cable ready to plug in. Everything is screwed. No soldering required.Mechanical hints for the replacement of the OLED display in the Yamaha DX5:The mechanical effort required to remove the display from the instrument is relatively simple in this case. The cover of the synthesizer can be lifted up after loosening a few screws. Now the circuit board on which the display is mounted must be unscrewed. The display itself is screwed on and the cable is plugged in.Recommendation:Disconnect the circuitry that generated the backlight voltage for the old display. Simply cut off two components using small side cutters.Instructions are included with the display.Note on OLED technology:OLED - organic light-emitting diode. The advantage of OLED technology is that each pixel is illuminated. This makes the OLED display easy to read from all sides, even from extreme viewing angles. Furthermore, it is also very easy to read in sunlight.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Yamaha TYROS 5 LCL CIRCUIT BOARDSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

CR2032 / CR2430 with solder tail suitable for YamahaRAM4 CardThis CR2032 is usable as spare part for the original used CR2430 in Yamaha RAM4 Card.Attention: Shipping for Europe only Please check right polarity! Maybe you have to rotate this part about 180 degrees.The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. CR2430 with solder tail suitable forYamaha RAM4 CardPlease check right polarity! Maybe you have to rotate this part about 180 degrees.Attention: Shipping for Europe only The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

8 position rotary switch 16 mm widht suitable forYamaha RS-7000Mechanical Description:Technical Description:Practical advice:These rotary switch is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Brandnew OLED Display BLUE suitable forYamaha TX802Based on our practical experience, we can offer you a complete mounting kit that contains everything needed to mount the new display. You only need to open the case and replace the OLED display. All you need is a screwdriver. The cable is plugged. This will be delivered:1 Brand new high Quality OLED Display, ready wiredMounting materialsMounting Instructions These different Display versions are available:BlueGreenYellowWhite The color of the shown display, may differ from the original. Installation service:We are also happy to install the display for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 to 100,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. LCD Display brandnew in Blue forYamaha TX802This is  a plug in ready Display replacement for Yamaha TX802. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired.On TX802 there is no contrast adjustment possible. We can not guarantee a optimal View. The color of the shown display, may differ from the original. These different Display versions are available:BlackOrangeWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Brandnew OLED Display GREEN suitable forYamaha TX802We have invested a few hours to customize this OLED display so that it can be used in the TX802. Based on our practical experience, we can offer you a complete mounting kit that contains everything needed to mount the new display. You only need to open the case and replace the OLED display. All you need is a screwdriver. The cable is plugged.  This will be delivered:1 Brand new high Quality OLED Display, ready wiredMounting materialsMounting Instructions These different Display versions are available:BlueGreenYellowWhite The color of the shown display, may differ from the original.Installation service:We are also happy to install the display for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 to 100,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Yamaha Tyros2 Holder Score StandThis housing is made of plastic

Digital-Analog-Converter for audio application for Roland E-PianosPCM56P von Texas InstrumentsThis part is used from RolandRoland      part number:15209122   Resolution:                    16bitInterface:                      seriellConversion rate:            666kS/sNumber of DAC outputs: 2Number of channels:      1Case:                           DIP16warm-up time:               1 minMechanical Description:The digital to analog converter is housed in a DIP 16 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The DA converter has 2 x 8 connecting pins with grid of 2.54 mm x 7.62 mm.Technical Description:This D/A converter was developed specifically for use in audio applications. The DA converter provides low distortion and typical differential linearity error is 0.001%. The interface is serial and provides a 16 bit resolution. The conversion rate is 666kS / s. For operation, no external components, such as temperature compensation or similar is required.It is a symmetrical supply voltage of +- 5V to +- 12V needed.

1 pcs. PCM54HP - Digital-Analog-Converter for audio application von Burr BrownThis part is used inKorg M1Korg T1Korg T2Korg T3   Resolution:                    16bitInterface:                      parallelCase:                           DIP28warm-up time:               1 minMechanical Description:The digital to analog converter is housed in a DIP 28 package and is designed for  classic through hole mounting on a circuit board. Use of a socket is possible. The DA converter has 2 x 14 connecting pins with grid of 2.54 mm x 15.24 mm.Technical Description:This D/A converter was developed specifically for use in audio applications. The DA converter provides low distortion and typical differential linearity error is 0.001%. The interface is parallel and provides a 16 bit resolution. It is a symmetrical supply voltage of +- 5V to +- 12V needed.

EPROM für Yamaha E-PianosPROM#39This part is used inYamaha PF10Yamaha PF15     

1 pcs. Rotary Potentiometer vertikal 12 mm with center TapCenter Tap function: no deviation in center positionSubstitute rotary potentiometer forYamaha RS7000Pitch Bend, ENV.DEPTH,SWING VELOCITY, CLOCK SHIFT MIDI DELAY, BEAT STRETCH GATE TIMEElectrical properties:The nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 12 mm bright, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has TAP function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Rotary potentiometer for LCD Contrast adjustment  The potentiometer is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Rotary Potentiometer new for Modulation 2  suitable forYamaha SY99 Modulation 2Resistance: 10 KOhm

1 pcs. Volume Slide potentiometer with 30mm travel. Suitable forYamaha SY77Yamaha SY99-------  Out of Production     --------Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Volume Slide potentiometer with 30mm travel. Suitable forYamaha EX5Yamaha Motif 6Yamaha Motif 7Yamaha Motif 8Yamaha QS-300Yamaha W5Yamaha W7-------  Out of Production     --------Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Slide potentiometer with 30mm travel. Suitable forYamaha SY77 - Data EntryYamaha SY99 - Data Entry This part is no longer availabel from Yamaha.This volume control with the labelling EWA-NFOC is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Slide potentiometer with 30mm travel. Suitable forYamaha Motif 6 - CS1 - CS4Yamaha Motif 7 - CS1 - CS4Yamaha Motif 8 - CS1 - CS4 This part is no longer availabel from Yamaha.This volume control with the labelling EWA-NFOC is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Volume Slide potentiometer with 30mm travel. Suitable forYamaha DX IIYamaha DX IIDYamaha DX IIFD-----     Discontinued - out of production    -------Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Slide potentiometer with 30mm travel. Suitable forYamaha DX II - Data EntryYamaha DX IID - Data EntryYamaha DX IIFD - Data Entry This part is no longer availabel from Yamaha.This volume control with the labelling EWA-NFOC is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 piece LED 3 mm Red with clear-diffused Body The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 piece bicolor LED 3 mm Red-green with clear-diffused Bodytecnical Hint:The housing of the LED is slightly flattened on one side. Same installation position as the original LED.The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. LCD Display yellow brandnew forYamaha TG55this is  a plug in ready Display replacement for Yamaha TG55 .We deliver this LCD Display plug in ready.With this Display we deliver some Parts for easy mounting and a short Instruction Manual.These different Display versions are available:BlueWhiteBlackYellowLifetime:The backlight lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.