Keyboards

1 piece LED 3 mm Red The LED are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required. 

1 pcs. Nut UNF 7/16 Inch for Phone JackTechnical descriptionThis nut fits to 1/4 Inch Phone Jacks. The nut is build from Plastic and has thread UNF 7/16 Inch. The thickness is 6/32 Inch and wrench size is 1/2 Inch. 

1 pcs. Rotary Potentiometer vertikal 12 mm with center TapCenter Tap function: no deviation in center positionYamaha RM1x      Utility Mounting instruction Yamaha RM1x:The potentiometer with thread I offer here can also be used in the RM1x. The great advantage of this solution is that I think potentiometers with threads will have much longer lifetime than potentiometers without threads. Indisputably, the axis is guided and stored much more stably by the thread.n the pictures you see a test installation I have made.Electrical properties:The nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 12 mm bright, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has TAP function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Yamaha Tyros  Speaker CableThis is a very short cable for direct connection from your Tyros to Speaker on Speaker Stand

Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used by  Clavia Nord PianosTechnical descriptionThe offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6     Bender-DCORoland Juno 60    Bender-DCOElectrical properties:The nominal resistance has 1 MOhm, the electric resistance gradient is logarithmic. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. new Slide potentiometer with 30mm travel. Suitable Slider forSlider forRoland Juno 6      ENV, KYBD,PWMElectrical properties:The nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,2 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins and the hight of housing, which today are no longer usual. In total four solder contact pins are laterally ordered to a group of two pins at the top and the end of the slide potentiometer.The slide potentiometer has a travel of 30 mm.Useful hint to Roland Juno Slider:The Lever of the original potentiometer has a strate shape. The Lever of the potentiometer offered here adapts to this shape because the Lever is slit.Arrangement of solder pins: The solder pins on this replacement part are arranged slightly offset. The solder pins must be bent slightly before soldering.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Slide potentiometer with 20mm travel. Suitable forYamaha Tyros 3    -   Assign Slider 1-8Yamaha Tyros 4    -   Assign Slider 1-8Yamaha Tyros 5    -   Assign Slider 1-8  Appearance (technical characterisation):The slide potentiometer has a travel of 20 mm.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. Phone Jack 1/4 inch- 6.3 mm, Stereo, for printed circuit with Iron FrameThe item is the same asHLJ 0544-01-010Technical description:The offered phone jack for PCB mounting is a mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating.Praktikal tip:Pay attention! The solder contacts are arranged staggertly.These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Yamaha Tyros Systemcable to SubwooferThis cable connects your Tyros with Subwoofer GNS MS01 

1 pcs. Knob for encoder knobs inRM1XMotif XS RackRS7000Praktical tip:The knobs are just plugged on. No tools are needed.

1 pcs. Quartz 9,6 MHzsuitable forYamaha DX7   Master Clock OSCYamaha DX9   Master Clock OSC

1 pcs. Pedal Volume PotentiometerThis is a replacement Poterntiomter for Pedal from E-Piano if there is a Volume Pedal installed.Electrical properties:The nominal resistance has 10 kOhm.Appearance (technical characterisation):This Potenziometer is a very spezial part. This one will only fit for Pedal.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs. Rotary Potentiometer for pitch bend  suitable forYamahaResistance: 10 KOhm

1 pcs.  slide Potentiometer forCasio CZ-1              VolumeCasio CZ-1000       VolumeCasio CZ-3000       VolumeCasio CZ-5000       VolumeThe Lever on original Potentiometer is shorter. You can cut this Lever to the right length.Electrical properties:The stereo nominal resistance has 10 kOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. DC Power Plug suitable for modelsKorg electribetechnical Dates:Termination SolderingMechanical Description:The housing of the Power Plug is made of Plastic and cable is soldered on it.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

Electrolytical Capacitor 10uF/25V SMDManufakturer: NichiconSerie: UQ for Audio Especially with SMD Elkos we often have the experience that these Elkos are often leaking after 20 years of operation and urgently need to be replaced.I offer here Elkos manufacturer Nichicon, these are used in audio, hi-fi and musical instruments.The UQ series was specially developed for use in audio technology.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

1 pcs. Slide Potentiometer with 30mm Travel. (Custom Built with dust cover for Synth-Parts)Suitable for forRoland JX-3PRoland SH-101      Env Attack, Decay, ReleaseThese potenziometer are brand new ALPS Potentiometer. Additional benefit is a dust cover diectly mounted on housing.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. new Contactrubber for Yamaha GHD KeyboardThis keyboard is used in these modells and others:Yamaha Clavinova CLP-120Yamaha Clavinova CLP-150Yamaha Clavinova CLP-220Yamaha Clavinova CLP-320Yamaha Clavinova CLP-880Yamaha Clavinova CLP-910Yamaha Clavinova CLP-930Yamaha Clavinova CLP-950Yamaha CVP-107Yamaha CVP-109Yamaha CVP-207Yamaha CVP-209Yamaha CVP-401Yamaha Motif 8 und Yamaha Motif ES8Yamaha P-80Yamaha P-120Yamaha P-200Color of these Contactrubber may be different.

1 pcs. OLED Display New forRoland Alpha Juno-1Roland Alpha Juno-2This OLED Display for Roland Alpha Juno-1 and Roland Alpha Juno-2 replacement is a really easy swapping. We will prepare this oled display in this way that ou will only need a screwdriver. Cable connection is done into a socket.Advice to Eprom Version in Roland Juno 1 and Juno 2Does the display only show half? That is, the first 8 characters are displayed normally but the remaining 8 characters remain dark? This can happen with an old Eprom version in the instrument. In this case the Eprom must be replaced by a current OS version.For Roland Juno 2 exists to different OS version 2.5. Only one supports OLED. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

Replacement Keys for Korg LS-88 KeyboardLS-88 keyboard is used inKorg Kronos 2 LS 88This keys are weightedColor: cream white (Ivory)The RealHammer 3 keyboard (RH3) is a touch-sensitive keyboard with 4-zone hammer mechanics.The unweighted keys have a length of 21.4 cm with a width of 2.24 cm. The depth of the key is 5.7 cm measured from the top of the key to the lower end of the key stroke. The top dead center stop is realized by a hook at the lower end of the key. The contactor, which presses on the contact strip, is not formed on the keyboard but on the hammer. At the back end, the key is held in the keyboard frame by means of a slot. The black keys have a length of 16.4 cm with a width of 1.2 cm. 4-Zone Hammer Mechanics:A 4-zone hammer mechanism is now state of the art for high-quality e-piano keyboards. By means of the four different zones the keyboard manufacturers try to get closer to the feeling of a mechanical wing. The keystroke on a mechanical piano varies depending on the area, whether bass or high. This is simulated with this keyboard by the fact that there are four different hammers with different weight. mechanical construction:The base of the keyboard is made of steel sheet and is very stable and rigid. All other components are attached to this frame by screwing or clamping. Particular mention should be made of the structure of the hammers. The hammers used here are made of a continuous metal part, which should guarantee a long life for these hammers. Only the attached plastic parts appear quite graceful.

1 pcs. Korg SP100 Volume Slide PotentiometerKorg SP100Korg SP200Korg SP250Korg SP300OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Encoder suitable forE-MU Command Station   E-MU E4K, E-SynthE-MU E4XT      depends on manufacturing dateE-MU e6400     depends on manufacturing date E-MU B-3Mo Phatt rack module or keyboardE-MU Planet EarthE-MU Orbit-3E-MU Proteus 2000E-MU Vintage ProE-MU Xtreme Lead 1 or XK-6 keyboard Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Encoder 16 mm widht suitable forKorg Electribe EMX1       only EC1Korg i2, i3, i4Korg Trinity, Trinity Plus, Trinity ProPractical advice:The thread of this encoder is 2 mm longer than the thread of the Original encoders. Depending on the space in the housing, it can tighten a bit when reassembling. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.