Keyboards

Korg RH4 Keyboard feltsRH4 keyboard is used in Korg SP-170Korg SP-280Krome 88All felt are fittet with self adhesive tape. For complete replacement of one 88 key keyboard you will need:2x Felt upper5x Hammer felt 12P - L11x Hammer felt L21x Hammer felt L3 

1 pcs. Pitch bend Assembly for Korg Music Production WorkstationKorg KronosKorg Kronos 2Korg Pa3XKorg Pa3X ProKorg Pa4XKorg Pa4X ProKorg Pa300Korg Pa600Korg Pa700Korg Pa900Korg Pa1000This pitch bend unit is complete and ready to plug in wired for easy exchanging this unit. To do this work you have to open your instrument. To exchange the unit unplug two connectors and there will be some srews. That is all. 

1 pcs. Yamaha GHL Actuate Rubber This rubber is used on every singel key as stopperColor: black

1 pcs. slide potentiometer with 30mm travel and 15mm Lever. Suitable forRoland HP-330Roland HP-530Attention: Lever - Slide pin must be shortende around 5 mmThis volume control with the labelling EWANNBX10B14 is no longer available from manufacturer Panasonic because the pot is not longer produced by them. We offer here a slide potentiometer with the same technical performance as the original part.Electrical properties:The stereo nominal resistance has 10 k? (Kilo-Ohm), the electric resistance gradient is linear. The potentiometer is construed for a power of 0,06 Watt.Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements. The particular embodiment of this potentiometer is the arrangement of the solder contact pins, which today are no longer usual. In total eight solder contact pins are laterally ordered to a group of four pins at the top and the end of the slide potentiometer. On both sides the solder pins are staggered in reverse order. Because of this arrangement the volume control fits only in a specific mounting position. The slide potentiometer has a travel of 30 mm. Its metallic casing measures 45 x 8 mm, the height without lever is 7 mm. The lever is made of black plastic and ends in corner radius. Its height is 15 mm, the breadth is 5 mm and its depth is 2 mm. The eight solder contact pins are 0,8 mm wide (one of them) and they are arranged in a distance of 3 mm. The bented pins are necessary for the electrical function.In medium range of the casing the metallic edge-socket connector is mounted. By these connectors the slide potentiometer will be fixed mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Kawai lower hammer Stopper Felt for E-Piano KeyboardsThis felt is used by Kawai in many keyboards and dampens the hammers when they are returning to zero position. In the drawing it is the felt with the number 37This felt consists of several layers of different materials.For better mounting this felt is equipped with an adhesive tape.  

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsKawai ES100Kawai ES110Kawai ES120Kawai VPC1This part comes directly from Kawai Europe.technical Dates:Termination Solder PinOuter Diameter: 5,9 mminner Diameter: 1 mmMechanical Description:The DC jack housing is made of plastic and the power jack is designed for direct board mounting.Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. 

1 pcs. AKAI MPC1000 Encoder special spare partTo replace the plastic shaft encoder in the AKAI MPC 1000.Encoder with plastic shaft: The wiring on the board has to be changed. We include instructions on how to do this with the order. For this work you need soldering skills and a piece of insulated wire.Mechanical note for the MPC1000 encoder:The axis of the encoder is approx. 0.5 mm longer than the axis of the original encoder in the MPC 1000. It can happen in rare cases that the encoder wheel scrapes the housing.Note on the OS version in the MPC1000:with older versions of the operating system in the MPC 1000 it can be that the encoder shows a different behavior. In this case please update to the current JJ OS.Practical advice:These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 pcs. Contact rubber for Kawai WN88 KeyboardA contact rubber consists of 12 contacts and covers an octave.Contact high:  11 mmStrip bright:   25 mmStrip length:  164  mmNumber of contacts: 12These contactrubber for e-pianos has been used in:Kawai CA48Kawai CA65Kawai CA95Kawai CS7Kawai CS10Kawai MP11Kawai VPC1A rubber contact strip consists of 12 contacts and covers an octave. For complete replacement of the rubber contact strips in a 88 Key keyboard you will need 8 strips with 12 contacts. One strip can be cut after 4 contacts.

1 pcs. HEC470-01-630 DC Power Jack with solder Pins for PCB mounting suitable for modelsYamaha P-85Yamaha P-140We offer the original Hosiden power socket here.technical Dates:Termination Solder PinMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

One Octave white Replacement Keys for Yamaha GHD KeyboardThis set contains:1 x A1 x B1 x C1 x D1 x E1 x F1 x GNote on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key. 

1 pcs E-mu Silent Fan Replacement 3HE RackWe offer here an Austasuch Silent fan for all E-mu rack instruments with 3 height units device size.Prepared ready to plug in. No soldering is required.Scope of delivery:    Fan with only 12dbA    Mounting material    Installation instructionsWith many of the E-Mu rack devices, the noise generated by the fan on the power supply unit is a major problem. The fan noise can be very annoying, especially in quiet studio environments.One noise will always remain. Whenever something moves, a noise is produced. So there is no such thing as a truly noise-free fan. But we offer the most powerful fan on the market. With the same technical data as the original fan.  

1 pc. Korg ESK7 Rubbercontact 6P x1 Features:    Height of contacts: 8 mm    width of the strip:   15 mm    Length of the strip: 80 mm    Number of contacts per strip: 6 contactsOne contact strip consists of 6 contacts and thus covers halfe octave. 

1 pcs. Clavia Nord Knob Drawbar Praktical tip:The knobs are just plugged on. No tools are needed. 

Encoder 16 mm widht suitable forYamaha RM1XYamaha RS-7000Practical advice:The thread of this encoder is 2 mm longer than the thread of the original encoders. Depending on the space in the housing, it can tighten a bit when reassembling. These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Single Button 17 x 7 mm (No Window)Korg Pa3XKorg Pa3X ProDo you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reason for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 17 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. Replacement rotary potentiometer suitable forRoland MC 303Roland MC 505Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

Complete Set tactile switch suitable for AKAI MPC-2000AKAI MPC-2000XL AKAI Part No: ES-411687NES-415015J  Quantity: 46 pcsThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required

1 pcs. Battery holder for CR2032 for PCB mountingAttention: Shipping for Europe only Technical Description:  Information for handling old Battery's

Replacement–set for broken key guides on Roland SK3 KeyboardsWith Roland Synthesizer and electric pianos, it can happen over time that the original key guides break because of aging. This leads to a hanging or grinding of the keys. Since there are no more original spare parts for old Roland instruments, we have been looking for an alternative. Through various application tests and material research, we have found a product that fulfills the characteristics of the original Roland key guides in an identical way. Therefore we offer you a matched spare part set for your Roland piano in our store.So that everyone can get an impression of our product and the handling or the exchange, we have prepared a suitable blog post and a PDF variant to print out. YIncluded in the set:– Matched tube suitable for a keyboard with 88 keys.Tecnical advice for Grease:As we know there was no use of grease in these old keyboards. 

1 pcs. tactile switch suitable for modelsWaldorf MicroqWaldorf MicrowaveWaldorf Microwave IIWaldorf Microwave XTThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. LCD display with LED backlightsuitable forRoland W-30We offer here a high quality replacement display with modern LED technology for the backlight.Mounting of LCD Display is plug and play. No soldering is required.Color: white font/blue backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable ready to plug in. Roland used in W30 a very special connector. We rebuild theses connector with handcraft pincompatible to the original one. Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland W30:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation. For this you have to cut two small componnents. No soldering is required.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.

1 pcs. HEC470-01-630 DC Power Jack with solder Pins for PCB mounting We offer the original Hosiden power socket here. Mechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 3 A at 16 VDC. Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.  

1 pcs. Nord Phone Jack 1/4 - 6.3 mm Stereo 2x Switch PCB used by Clavia Nord PianosTechnical descriptionThe offered phone jack for PCB mounting is a stereo jack with two switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. This phone jack is often used on Clavia Nord instruments for the control pedal and rotor pedal. (This information is without guarantee - please have a look on pinlayout of the phone jack. The pin layout of phone jack is unique.Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

18 pin FFC socket with 2.54 mm pitch18 pinPitch: 2.54 mmLength: 51,18 mmdeepth:  4,50 mmhight:      6,70 mmThese socket is used in Korg Poly 61 between KLM-475 and KLM-476Technical description