Keyboards

1 pcs. Yellow LCD Display with LED Backlight replacement including cable Kit forKorg 01R/W We offer an absolutely equivalent display using modern LED technology for backlight.Color: black Character  /  Yellow BackgroundDelivery scope of LCD Display Set:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01R/W:The instrument must be disassembled almost completely to reach the display.The rack version of the Korg 01/RW synthesizer has much less mechanical effort than the keyboard versions.For the new display to work, one SMD resistor on the mainboard of the Korg 01/RW must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/RW have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people 

1 pcs. Music stand for Technics KeyboardTechnics KN5000This music stand is placed at the rear sideMounting: reare sideMounting design: plugMaterial: Metal, blackz anodizedwide range Note pad: 48 cmwide range top:         45    cmhigh:                        20   cmHole distance:           46,5 cmDiameter hole :             5 mm

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu DarwinWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  /  white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD in Emu Darwin:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu DarwinWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

1 pcs. Korg X5D OLED Display New forReady to plug in OLED Display for replacement in Korg X5D. No soldering is required.Mechanical modification is required.The original LCD display in the Korg X5D is screwed onto fixed mounting bolts, whereby the distance to the front panel is fixed. Since the OLED display is much flatter than the original LCD display, there is a tunnel effect with the OLED. It is possible to shorten the mounting bolts in the Korg X5D. This work requires skill and good fine motor skills.For the actual assembly of the new OLED display in the Korg X5D only a screwdriver is required.Scope of delivery of the OLED Display Set:OLED Display ready wiredPlease choose you favorit color. Lifetime of OLED Display:The lifetime is specified by the manufacturer with 40,000 to 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Quasimidi button cap clear Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 19 x 7 mm. This part has one Button.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

1 pcs. Korg X2 Volume Slide PotentiometerKorg X2Korg X3Korg X5Korg X5DOEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Korg i2 Volume Slide PotentiometerKorg i2Korg i3Korg i40Korg i50OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

Contact PCB for Yamaha 16NW keyboard PCB high

1 pcs. Phone Jack 1/4 inch, Mono for printed circuit 2 switchSpecification:MonoThread: UNF 7/16 InchHousing: PlasticThese phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Nch Power MOSFET FQP2N90 - Replacement for 2SK1199 Housing:  TO220VDss:      900VId:          2.2APd:          85WTechnical hint:suitable replacement for PSU in Korg T1,T2,T3 

1 pcs. Floppy2USB Emulator suitable for Yamaha 9000Pro We deliver this Floppy2USB drive with a suitable adapter cable. The installation is easy to accomplish.Much more complex is the transfer of the floppy disks to the USB stick. This requires an old PC that still has a floppy drive and a USB post. Here there is a software that supports copying.

1 pcs. OLED Display New forAlesis HR-16mechanical work is required on Alesis HR-16:The display is mounted on plastic bolts that are firmly connected to the housing. These plastic bolts must be shortened. The height of the OLED display is much lower than the height of the original LCD display. Without adjustment of the plastic bolts, a tunnel effect occurs because the new OLED display is much too deep in the housing.The screws from the original display can be reused.No soldering is required. The required plug is already soldered on and the cable is only plugged on.The color of the display shown may differ slightly from the original.Lifetime of OLED Display:The lifetime is specified by the manufacturer with 50,000  operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. OLED Display brandnew in yellow forRoland JD-800this is  a plug in ready Display replacement for Roland JD-800. You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired. The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Service Kit Kawai RJ88B PWB Assy KKB-034(2)This service kit replaces the circuit boards and contact rubbers in the Kawai RJ88B keyboard. Only possible as a replacement for keyboards in which contact rubbers with two contacts per tone were used.The set consists of two boards, fully equipped with new contact rubbers.These Board fit in these e-pianos:Kawai ES110Kawai ES120

1 pcs. Roland JD800 Encoder Board newThis Encoder PCB is suitable forRoland JD800Mechanical Description of Encoder Board:we deliver a brand new Encoder and a PCB ready mounted, herer you can just plug in the original cable. The cable is just pluged in and has to be taken over from original Encoder Board.This new Encoder has housing from Metall and a plastik axis.Practical advice for Mounting JD800 Encoder PCB:The circuit board must be machined:The new encoder has a larger thread than the original encoder in the JD-800. Furthermore, there is a pin on the encoder to prevent mechanical rotation of the component. The mounting hole for this pin must be re-drilled. The exact drilling plan can be seen in the pictures.The enlargement from 7 mm to 9 mm can be done by hand with a standard metal drill. This is gentler than working with a machine. 

1 pcs. Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used in  Korg Instruments Technical description :The offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. This phone jack is available from various manufacturers in the same mechanical and technical construction. An exception is the manufacturer HOSIDEN using a wider housing. The electrical connection has the same structure.Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs Kawai INLET Board KEP-389(22)THis PCB is used inKawai CA95Safety note: This assembly is in direct contact with 230V AC mains voltage. Only for qualified electricians.Electrical properties of KEP-389(22):Voltage: 230 V ACFuse on Board: 1,6Afor use in EuropePractical advice:Plug of the device. Don't work under Voltage. 

1 pcs. Yamaha FSX Stopper U 76This FSX keyboard is used in these modells and others:Yamaha Motif XS7 

1 pcs. PCB ASSY DM TYROS3Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Yamaha GHD CL A88 Keyboard complete This keyboard is used in these modells:Yamaha CLP-150Yamaha CLP-320Yamaha CP-40Yamaha CP-50Yamaha CP-300Color: cremewhite--- shipping only in germany, sorry  ----- 

1 pcs. Roland PG-1000 OLED Display Yellow NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Roland PG-1000 OLED Display green NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Yamaha GH3 Stopper U88 with AftertouchThis GH3 keyboard is used in these modells and others:Yamaha Montage 8This felt is special for GH3 Keyboards with Aftertouch