Keyboards

1 pcs yellow LCD Display with LED Backlight replacement including cable Kit forKurzweil K2000Kurzweil K2000rKurzweil K2000 VX We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  white BackgroundDelivery scope of Display set:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtion Notes on installation of LCD Display in Kurzweil K2000:The instrument must be almost completely disassembled to access the display. Please do not underestimate the amount of work that is necessary. This work should only be carried out by people with technical, preferably electrotechnical, experience.The installation itself can be done without any soldering skills, but: We recommend to take out of function circuit part for the old backlight foil. For this, a transistor and a capacitor must be removed. This can also be done with a side cutter, i.e. without soldering. 

1 pcs. Yamaha Round KnobYamaha DGX-500Yamaha DGX-530Yamaha P-155Yamaha PSR-S700Yamaha PSR-S710Yamaha PSR-S900Yamaha PSR-S910 Technical Description of Yamaha Knob:This Round knob will be put on rotary potentiometer on your Yamaha Stage Pianos 

1 pcs. new Brand new OLED Display forKurzweil K1000 AX PlusKurzweil K1000 HXKurzweil K1000 PXKurzweil K1000 SXBrand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1000  Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1000 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

1 pcs. duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for modelsE-Mu  -  Mounting Frame must be taken overPlease note: Not suitable for all E-Mu devices.technical Dates:Voltage: 250VACCurrent: 6ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for soldering. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 15 mm, a length of 30 mm and a height of 9 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. Encoder 16 mm wide with Detends suitable forWaldorf Microwave 2The Waldorf Microwave II has one of these encoder with detents. These encoder is mounted beside the display.Practical advice:The axis of this encoder is 2 mm longer than the axis of the original encoder of the Waldorf Microwave 2. Under circumstances the axis must be shortened. Since the axis of the encoder is made of plastic, shortening is quite easy.These encoder is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Recapping set for Waldorf Microwave 2The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Waldorf Microwave 2 is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for complete Waldorf Microwave 2The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. LCD display with LED backlightsuitable forRoland W-30We offer here a high quality replacement display with modern LED technology for the backlight.Mounting of LCD Display is plug and play. No soldering is required.Color: black font/white backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable ready to plug in. Roland used in W30 a very special connector. We rebuild theses connector with handcraft pincompatible to the original one. Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland W30:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation. For this you have to cut two small componnents. No soldering is required.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 02Roland D-70, mainboard version 03We offer here a high quality replacement display with modern LED technology for the backlight.Color: white font/black backgroundScope of delivery of LCD Display set:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description! Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly LCD Display for Roland D-70:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", "02" or "03". 

1 pcs. Korg 01/W Volume Slide PotentiometerKorg 01WKorg 01/W FDKorg 01W ProKorg 01/W ProXOEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Korg T1 Volume Slide PotentiometerKorg T1Korg T2Korg T3OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Korg Wavestation Volume Slide PotentiometerOEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Korg N1 Volume Slide PotentiometerKorg N1Korg N264Korg N364OEM Part: Original Equipment Manufacturer: We purchase this potentiometer from the same manufacturer as Korg did.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Roland MKS-50 OLED Display brandnew Ready-to-plug display for the exchange in the Roland MKS-50. For this exchange you only need a screwdriver. We deliver the display ready wired.Roland used a display in the MKS-50 which is no longer available. So that our new OELD display can be installed without problems, we have developed a compensation frame. The display is mounted on this frame. The compensation frame for the OLED display in the Roland MKS-50 is included in delivery. Advice to Eprom Version in Roland MKS-50Does the display only show half? That is, the first 8 characters are displayed normally but the remaining 8 characters remain dark? This can happen with an old Eprom version in the instrument. In this case the Eprom must be replaced by a current OS version.Notes on installation OLED Display in Roland MKS-50:We deliver this OLED dislpay for the Roland MKS-50 synthesizer ready for installation. All necessary cables are already soldered on. We deliver a 3D printet frame for mounting OLED in your Synthesizer. You will only need a screwdriver for the installation.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service:Please ask.Lifetime of OLED Displays:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

Recapping set for Roland MKS-50The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the complete Instrument.The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. COIL ASS'Y (AL) L=75 BL SX100/RSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. Roland PG-1000 OLED Display white NEW, LCD ReplacementOLED display upgrade for the Roland PG-1000 programmer. This new OLED display upgrades the visual appearance of the Roland PG-1000 programmer. OLED displays convince with a very good readability from all viewing angles. Even in sunlight, OLED displays are easy to read.This OLED Display for Roland Programmer PG-1000 replacement is a really easy swapping. We will prepare this oled display in this way that you will only need a screwdriver. Cable connection is done into a socket.No soldering is required Notes on installation:- Recommendation: Take out of function the circuit part that generated the backlight voltage for the old display. It is sufficient to cut off two components with a small side cutter.- Instructions are enclosed with the display.Lifetime of OELD Display:The lifetime is specified by the manufacturer with 40,000 operating hours. Lifetime is different and depends on used color. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Kawai Volume Slider 30mm Travel The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Clavia Nord 4 way Power Supply IEC14 V1.3  brand new replacement power supply for many Clavia Nord models.Please pay attention to the mains connection: This power supply has a 3-pin IEC C14 connector. Older Clavia Nord models use a 2-pin Euro connector. Secondary side: 10-pole ribbon cableThis Power supply deliver:+ 3.3 Volt+5 Volt+/-12 VoltSafety note: Here you are working directly on the mains voltage of 230 VAC. This work is only suitable for people with appropriate electrical knowledge. 

1 pcs. Korg M1R OLED Display brandnew in white this is  a plug in ready OLED Display replacement for Korg M1R Rack Synthsizer. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.To install this OLED replacement display in the Korg M1R, first remove the housing cover of the synthesiser. The front panel is then removed. The display is now accessible and can be unscrewed. When mounting the new OLED display in the Korg M1, please use the spacer sleeves supplied.Not compatible with Korg M1 Keyboard version. This Display is a separate item.The color of the shown display, may differ from the original.Installation service for Korg M1R:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs.  Yamaha FFC cable for GHL KeyboardKeyboard connection cableThis cable connects Yamaha GHL Keyboard with Mainboard   

1 pcs. Roland JP8000 OLED Display brandnew in white this is  a plug in ready OLED Display replacement for Roland JP8000 Synthsizer. For this display replacement, we strongly recommend shortening the mounting bolts in the housing of the Roland JP8000. The OLED display itself is supplied pre-wired. No soldering is required Mounting instructions for Roland JP8000 OLED:The mechanical assembly of this OLED display is somewhat more complex. The synthesiser is opened from the back and almost all components have to be removed to access the display, unfortunately the keyboard also has to be removed.The display assembly in Roland JP-8000:We have developed a special cable adapter for the display in the Roland JP8000. This makes it possible to continue using the flat cable used in the original. The flat cable is simply plugged in.The display in the Roland JP8000 is mounted on plastic bolts that are firmly connected to the display frame of the synthesiser, but these plastic bolts are much too high for the new OLED display at 8 mm. It is best to shorten these bolts to 5 mm so that the new OLED display comes very close to the windscreen. These plastic bolts can be easily sawn off with a small modelling handsaw. In our picture it is a saw from Tamiya.The big advantage is that a shim can be placed underneath as a height stop. This allows me to saw off the correct height very safely.Scope of delivery Roland JP8000 OLED Display:OLED display ready wiredInstallation instructionsmounting materialThe color of the shown display, may differ from the original.Installation service for Roland JP8000:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Korg M1 OLED Display brandnew in yellow this is  a plug in ready OLED Display replacement for Korg M1 Keyboard Synthsizer. For this display replacement, we strongly recommend shortening the mounting bolts in the housing of the Korg M1. The OLED display itself is supplied pre-wired. No soldering is requiredNot compatible with Korg M1R Rack Synthesizer. This Display is a separate item.Mounting instructions for Korg M1 OLED:The mechanical assembly of this OLED display is somewhat more complex. The synthesiser is opened from the back and almost all components have to be removed to access the display, unfortunately the keyboard also has to be removed.The display assembly: The display in the Korg M1 is mounted on plastic bolts that are firmly connected to the display frame of the synthesiser, but these plastic bolts are much too high for the new OLED display at 10 mm. It is best to shorten these bolts to 5 mm so that the new OLED display comes very close to the windscreen. These plastic bolts can be easily sawn off with a small modelling handsaw. In our picture it is a saw from Tamiya.The big advantage is that a shim can be placed underneath as a height stop. This allows me to saw off the correct height very safely.Scope of delivery Korg M1 OLED Display:OLED display ready wiredInstallation instructionsmounting materialThe color of the shown display, may differ from the original.Installation service for Korg M1 Keyboard:We are able to do this replacement for you. Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. ITT SAA1004 - Frequency Divider ICOld stock - every single component has been checked by us for function. FeaturesClock frequency from 20Hz to 20KHz Package: DIP-14Pin-compatible with SAJ110 Mechanical Description SAA1004 : The IC is housed in a DIP 14 package and is designed for trughhole mounting on a circuit board.ICs are sensitive to static charge! Handle with care.Semiconductors are excluded from exchange.