Keyboards

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu E4KE-mu E-Synth We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes for installing the LCD display in the E-Synth:The display is prepared by us ready for plugging in. All adjustments to the technical specifications of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. We recommend removing this part of the circuit. In this case, an SMD transistor must be desoldered.We would nevertheless like to point out that there is very little space in most devices. This work should only be carried out by technically experienced individuals. Installation service for LCD Display:We are also happy to install the display for you. Please ask. 

1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha CLP-545Yamaha CLP-565GPYamaha P-125This potenziometer is used for volume control, but it is a mono potenziometer. Not Stereo and this is correct in this case.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Yamaha Pedal screwDimensions: M6 x 57 mm Note:At 25 mm, this pedal support bolt has a shorter thread than the one under item numberSCYA-ZY898700

1 pcs. Slider with 45mm Travel. Suitable for Yamaha Motif ESYamaha Montage 6 Main VolumeYamaha Montage 7 Main VolumeYamaha Montage 8 Main VolumeThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Power cabel 3m with 3P C13 plug   

Contact rubber for Roland SK9 Keyboardstechnichal dimensionsNo of contacts: 7,8, 12 or 13Width: 21 mmheigh: 9.8 mm

1 pcs. OLED Display New forCasio CZ-1Casio CZ-101Casio CZ-1000Casio CZ-2000SCasio CZ-2600SCasio CZ-3000Casio CZ-5000The display has been prepared by us ready to plug in. We supply the display ready with the cable fitted for replacement in the synthesiser. All you need for this replacement is a screwdriver.Note on special characters: Casio uses special characters in the display of various instruments, e.g. note symbols. These symbols cannot be shown on the OLED display.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. OLED Display New forYamaha DX21This Display replacement is a really easy swapping. You will only need a screwdriver.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 50,000 to 100,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Encoder 16 mm widht suitable forYamaha Tyros 1Yamaha Tyros 2Yamaha CVP-207Yamaha CVP-209 Part numbers:Yamaha      VU48130R  REB161-PVB  

Brand new OLED Display, green, forKurzweil K1200 Pro 1Brand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1200 Pro 1 Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1200 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation. Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

Recapping Set for Korg DW8000The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Korg DW8000  series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.If no longer available from Nichicon, we use Würth or Rubycon Capacitors.This Recapping Set contains all necessary Capacitors for Korg DW-8000 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. yellow LCD Display with LED Backlight replacement including cable Kit forAKAI MPC-1000We offer an brand new display with LED technology for backlight. Display is ready mounted, no soldering is requiered.Display with black letters and yellow-green backlightDisplay design upgrade:AKAI has built in a display with a yellow-green backlight that breaks out of the housing and disturbs the elegant appearance of this instrument. We offer a new display that matches the black case of the AKAI MPC-1000. The display fits harmoniously into the design of the sampler.The color of the shown display on picture, may differ from the original.Color: Black Character  /  yellow BackgroundDelivery scope:Display is ready wired on delkiveryMounting parts if necessaryNotes on installation:The display is prepared by us ready wired and no soldering is required. All adjustments to the technical features of the MPC sampler are made by us on the display. Plug and Play installation. The new display is installed in exactly the same way as the old display was removed. For this reason, we do not provide installation instructions here. Nevertheless, we would like to point out that there is very little space in most devices. This work should only be done by technically experienced people.When switching on the new display for the first time, the optimum contrast point must be adjusted. This is achieved by pressing and holding the Stop key and turning the data wheel.  Installation service:We are also happy to install the display for you. Please ask.  

Replacement Keys for Yamaha NL2 KeyboardThese Keys fits for all Yamaha NL2 keyboards.Yamaha NL2 keyboard is used in:Yamaha CP5Note on the keys supplied:The keys are delivered without the black rubber that is mounted at the bottom of the key. The black rubber is taken from the old key. The rubber is clicked in and can be easily replaced. The Yamaha NL2 keyboard is a velocity-sensitive keyboard. The keys have a wooden core that is covered with plastic.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

Yamaha GHL Key's  This keyboard is used in these modells:Yamaha P-120Yamaha P-125Yamaha YDP-S30Yamaha YDP-143Color: whiteNote on the keys supplied - black rubber:The keys are normally supplied without the black rubber buffer that is attached to the lower end of the key. The black rubber must be taken from the old key.mechanical construction:Keys for this Keyboard are not available as single keys. One Octave will be a set of three single spare parts. One part for the black Keys. One part for D/A/F, and one part for C/E/F/B.

1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVE-mu e64We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  /  white Background Delivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping is eliminated)lifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. In this case one part must be desoldered.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people. Installation service:We are also happy to install the display for you. Please ask.

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forYamaha TG77We offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope of LCD Display Replacmeent:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation the Display in Yamaha TG77:Inside Yamaha TG 77 is very little space for the new display. A circuit board is mounted behind the display, it is called switch panel. On this switch panel a number of diodes are soldered which can collide with the new display. It is highly advisable to move these diodes to the back of the switch panel.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs new LCD Display with LED Backlight replacement including cable Kit forKorg WavestationKorg Wavestation A/DKorg Wavestation EXWe offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument. Please let us know your instrument. Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display. Furthermore, you have to solder on wire bridge in your synthesizer. And you have to cut some elektronic parts to take out of control old Backligth section.This work is to be done only by technically, best electrotechnically savvy people. 

Roland Roland Juno SH-101 Fader Set comlete (Custom Built with dust cover for Synth-Parts)This Set contains:3   pcs. Fader 30mm    100KA  -  ALPS10 pcs. Fader 30mm    100KB  -  Taiwan Alpha3   pcs. Fader 30mm    1MKA  -  ALPSUseful hint:Potentiometer are soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

Yamaha FSX  Keyboard contact PCBThis PCB is used inYamaha Tyros 2Yamaha Tyros 3Yamaha Tyros 4

1 pcs.  Roland JD800 FFC cable 26 pinKeyboard connection cablein Roland JD-800 Service Manual this cable is called FUJI CARD 26x420This cable is the connection cable between the Mainboard in Rolands JD800 and the Contact Board Assy under the Keyboard.There are 2 different keyboard cables in the Roland JD-800:According to our research, there exists two different keyboard versions in Roland JD-800, which means there are two different versions used of this cable. The difference in this cable is, in one type of this cable contacts are on the same side of cable. In second type of this cable contacts  are on one side on top and and on the opposite side at the other end of the cable contacts are down under.Please take a close look at your Roland JD-800 before ordering this cable. We have both cable versions on offer.This cable was produced in Germany in best qualtity.Length = 420 mmOpposit side connector 

1 pcs. OLED Display brandnew in white forRoland D-50this is  a plug in ready Display replacement for Roland D-50. You will only need a screwdriver for this replacement.We deliver this OLED Display ready wired.Notes on installation of OLED Display:We deliver this OLED dislpay for the Roland D-50 synthesizer ready for installation. All necessary cables are already soldered on. You will only need a screwdriver for the installation.- Recommendation: The new OLED display has only one cable. The second cable as with the original LCD Display in the Roland D-50 is omitted.- Instructions are enclosed with the display.The color of the shown display, may differ from the original.Installation service for LCD and OLED Display:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. Blue LCD Display with LED Backlight replacement including cable Kit forKorg 01R/W Rack ModulDisplay for Korg 01/W Keyboard Version please order hereWe offer an absolutely equivalent display using modern LED technology for backlight.Color: White Character  /  Blue BackgroundDelivery scope for LCD Display:Display ready wiredMounting partsOne SMD ResistorInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation of LCD Display in Korg 01/RW:The instrument must be disassembled almost completely to reach the display.The rack version of the Korg 01/RW synthesizer has much less mechanical effort than the keyboard versions.For the new display to work, one SMD resistor on the mainboard of the Korg 01/RW must be replaced.Furthermore we recommend to take out of function the power supply for the old backlight. For this two components in the Korg 01/RW have to be cut or desoldered. With this change the annoying beeping is eliminated.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. LCD display with LED backlightsuitable forRoland D-70, mainboard version 00Roland D-70, mainboard version 01We offer here a high quality replacement display with modern LED technology for the backlight.Color: white font/black backgroundScope of delivery:Display with connection cableMounting accessoriesManual The delivery includes an already soldered cable and a connection adapter suitable for your mainboard.Please note the information at the end of the article description!Advantages of a display with LED backlight:much brighterhigh-frequency noise (beeping) of the transformer is eliminatedmuch longer lifetime of the backlight compared to the lifetime of EL-filmslower power consumptionNotes on assembly for LCD Display in Roland D70:The instrument must be almost completely disassembled to access the display.We strongly recommend to take the circuit part, which generates the backlight voltage for the old display, permanently out of operation.This procedure is described in the manual. This work should only be done by technically, preferably electrotechnically skilled people.CAUTION!Roland delivered the D-70 synthesizer with two revisions of the mainboard.In order to supply you with the correct version of the necessary connectors, it is important that you know the revision number of your mainboard before ordering this replacement display.Please order the version of our custom made, high quality replacement part that fits your D-70 synthesizer.This will save you from a possible wrong order.You will find the version designation in the upper left corner of your mainboard. Behind "ASSY 76237130" you will find either "01", or "02". 

Slider set brand new Sequential Circuits, SCI Potentiometer forSequential Circuits Prophet 5 REV2     Serial 183 - 1300The potentiometers that were installed in the Prophet 5 have a significant disadvantage. This disadvantage is that the axis used was made of Plastic. This plastic axle breaks off easily and it is no longer possible today to get the original spare parts. A potentiometer with metal axis.Appearance (technical characterisation):We offer here a brand new potentiometer as a replacement for the potentiometer used in Sequential Circuits synthesizers.Resistance: 100 KOhmQuantity: 26 pcs.Changes to the original Pot:+ Metal axle instead of plastic axle.o 8mm thread          Original potentiometer has inch thread with 9.5mm- Soldering pins are 2 mm wide. The original is 1.5 mm.      The holes in the board are 2,08 mm wide. Maybe holes have to be drilled with a bit.Usefull hint:Delivery includes Nut and Washer.Since this is a two-sided board, please note, when soldering the new potentiometer must be soldered on both sides.The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.