Products

1 piece Elko 3,300uF/16V for Audio circuitsManufakturer: NichiconIn E-Pianos, Synthesizern and Keyboards bipolar electolytical capacitors are used for audio signal decoupling in Audio signal path. After 20 years these capacitors  are aged. In much cases the messured capacity after 20 years of use is 20 % distant from par value.Here i offer a special Capacitor from manufakturer Nichicon. The KA series  is developed  especially for use in audio equipment.The capacitors are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.

NEW Replacement Keys, weighted for Roland SK8 Synthesizer Keyboardused inRoland XP-30Roalnd XP-80This are new Key's without "Red Glue-Problem" 

Replacement keys, weighted for Fatar TP10 Keyboard with pressure point Fatar TP10 keyboard is a touch sensitive keyboard with Hammer Action. The weighted Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.A pressure point simulation is entered in the keyboard variant. This is done by means of a nose formed on the Key, which protrudes downwards into the keyboard frame. The weighted keys have a length of 21.8 cm and a width of 2.24 cm. The thickness of the keys is 1,5 cm.The contactor, which presses on the contact strip is 2.8 cm deep. The distance between the front contact and the front of the keyboard is 14 cm. The keys are in color cream white.The plastics used by Fatar tend to darken very strongly and the plastic becomes somewhat brittle.

Replacement keys for Fatar TP/9P E-Piano Keyboardused inRoland A-30Roland A-33Roland A-37 Fatar TP/9P keyboard is a touch sensitive keyboard. Keys are mounted on a support frame with core of steel sheet. At these core all attachments were made of plastic in an injected machine.contact detection is done via 12 pin contact rubber strip with two graphite points.The weighted keys have a length of 16 cm and a width of 2.24 cm. The thickness of the keys is 1 cm.The contactor, which presses on the contact strip is 1.9 cm deep. The distance between the front contact and the front of the keyboard is 10,5 cm. The keys are in color cream white.Comment:We know three different Version of this Keyboard: TP/9S, TP/9P and TP/9+. Please have a exact look at the pictures. The plastics used by Fatar tend to darken very strongly and the plastic becomes somewhat brittle.

1 pcs. Contact rubber SK30 for Technics Keyboard - diskontinued -used in:Technics KN-720Technics KN-920Technics KN-930Technics KN-1400Technics KN-1500Technics KN-1600Technics KN-2400Technics KN-2600This are brand new contact rubbers.A contact rubber consists of 12 or 13 contacts and covers an octave. A rubber contact strip consists of 12 or 13 contacts and covers an octave. For complete replacement of the rubber contact strips in a keyboard with 61 keys you will need 4 contact rubber with 12 contacts and 1 contact rubber with 13 contacts.

Replacement Keys for Technics KeyboardsThis Keyboard with single Keys is used by Technics in many of there Keyboards.These Keys are unweigted and in Color Creme White also called Ivory.This parts are usedImportant NOTE:For this Keyboard Version Tehnics used different P.C.B.'s and differernt Contactrubber. Please have a exact look on your Keyboard if you need a replacement P.C.B or replacement Contactrubber.

Parts for Pedal Assembly Technics E-PianosComments on the article:That's why the pedal is only available as an article pedal center.We deliver the spring that we currently have in stock.The spare parts are usually used. Please see specification for exact item.

Molex Poke In Socket 3 PolThis connector series from Molex is today out of production.These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Key's 16N-W Style suitable for Yamaha This keyboard is used in these modells:Yamaha MOX6Yamaha Tyros 1Color: whiteThe white Keys are weighted.The black keys are unweighted.This key is newmechanical construction:Keys for this Keyboard are not available as single keys. One Octave will be a set of three single spare parts. One part for the black Keys. One part for D/A/F, and one part for C/E/F/B.

1 pcs. Yamaha FU80 AC-IN BoardFor Europe only: 230VAC

1 pcs. 16 pin FFC socket with 1.25 mm pitch16 pinPitch: 1.25 mmLength: 23,75 mmdeepth:  4,80 mmhight:      7,80 mmTechnical description

Keys, weighted for Roland SK9 KeyboardThis part fits for all Roland SK9 KeyboardsRoland SK9 Keyboard is used inFantom (FA76)Fantom G6, G7Fantom SFantom X6, X7XP-10Color/tint: pure white 

Pedal Assembly Version 2 for Yamaha E-Pianos XR780The differrenz is to see in Pedal PCB. This PCB is without ground cable.Practice tip:Yamaha has built in a socket on the boards, which are built into the pedal which is perpendicular to the board. Here, the cable is plugged in that leads to the electronics of the electric piano in the upper part. As a result, this beech breaks out in the course of the operating years and it comes to the failure of the pedal.In most Repartur cases, it will be enough just to swap the socket. 

Brand new OLED Display, white, forKurzweil K1200 Pro 1Brand new OLED display as a replacement for the originaly used LCD display. No Soldering required.This OLED Display fits in the K1200 Pro 1 Rack Version onlyHints for mounting:This new OLED Display for your Kurzweil K1200 kann be replaced very easy because your replacement OLED Display is a 1:1 replacement. The new OLED display will be delivered by us readily wired.No soldering work is necessary for this installation.Scope of delivery:1 pc. new OLED display, ready wiredMounting materialshort installation instructionNotes on disposal:Every electronic component contains important raw materials that should be recycled. Please find out where in your city is a corresponding collection point for these components.

1 pcs. LCD Display brandnew in blue forKorg M1Rthis is  a plug in ready Display replacement for Korg M1R . You will only need a screwdriver for this replacement.We deliver this LCD Display ready wired. The color of the shown display, may differ from the original.These different Display versions are available:BlueblackWhiteYellowInstallation service:Please ask.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. black LCD Display with LED Backlight replacement including cable Kit forAKAI MPC-1000We offer an brand new display with LED technology for backlight. Display is ready mounted, no soldering is requiered.Display with white letters and blue backlightDisplay design upgrade:AKAI has built in a display with a yellow-green backlight that breaks out of the housing and disturbs the elegant appearance of this instrument. We offer a new display that matches the black case of the AKAI MPC-1000. The display fits harmoniously into the design of the sampler.Display defective?Our display is also suitable as a replacement part if the original LCD display is defective. It doesn't matter if only the backlight is no longer working or if the LCD is without function. Our display is perfectly suitable as a replacement display for the AKAI MPC-1000 sampler.Or are you looking for a Christmas present?Are you looking for a gift for an ambitious musician who works a lot with AKAI samplers or who has always been annoyed by the original display? How about a new display that visually enhances the device and also increases the value of the instrument.Unfortunately, we cannot offer the complete instrument, but only a new LCD display.The color of the shown display on picture, may differ from the original.Color: White Character  /  blue BackgroundDelivery scope:Display is ready wired on delkiveryMounting parts if necessaryNotes on installation:The display is prepared by us ready wired and no soldering is required. All adjustments to the technical features of the MPC sampler are made by us on the display. Plug and Play installation. The new display is installed in exactly the same way as the old display was removed. For this reason, we do not provide installation instructions here. Nevertheless, we would like to point out that there is very little space in most devices. This work should only be done by technically experienced people.When switching on the new display for the first time, the optimum contrast point must be adjusted. This is achieved by pressing and holding the stop key and turning the data wheel.  Installation service:We are also happy to install the display for you. Please ask.  

1 pcs. triple MIDI DIN socket female 5 pin for printed circuit for E-MuJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. This is a 1:1 replacement for the MIDI jack in most e-mu sampler.These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E4XTE-mu e6400We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  /  white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

11 pcs. Slide potentiometer with 20mm travel. Suitable forRoland TR-707Appearance (technical characterisation):This slide potentiometer has been built in in the past in many instruments and audio equipements.The slide potentiometer has a travel of 20 mm.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.

1 pcs. LCD Display with LED Backlight replacement including cable Kit forYamaha TG77We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:Inside Yamaha TG 77 is very little space for the new display. A circuit board is mounted behind the display, it is called switch panel. On this switch panel a number of diodes are soldered which can collide with the new display. It is highly advisable to move these diodes to the back of the switch panel.This work is to be done only by technically, best electrotechnically savvy people.

1 pcs. blue LCD Display with LED Backlight replacement including cable Kit forE-mu e5000 UltraWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask. 

1 pcs AC Power Inlet EU with Solder Pins for PCBCONNECTORINLET CCT2302-1372 ELB-02Ktechnical Dates:Termination Solder Pins2 pol Electrical properties CCT2302-1372 ELB-02K:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2,5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage. 

1 pcs. Black LCD Display with LED Backlight replacement including cable Kit forKorg i2Korg i3We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play Display. No soldering is requiered.Color: White Character  /  Black BackgroundDelivery scope of Display Set:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation LCD Display:The instrument must be disassembled almost completely to reach the display.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people.  

1 pcs. new LCD Display with LED Backlight replacement including cable Kit forKorg i2Korg i3We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play Display. No soldering is requiered.Color: Black Character  /  White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:The instrument must be disassembled almost completely to reach the display.We recommend taking the power supply for the old display backlight out of operation. To do this, remove a transistor and a capacitor in the power supply. We have described this in our instructions.This work is to be done only by technically, best electrotechnically savvy people.