Yamaha R-Serie

1 pcs external Class A Power Supply Unit equivalent to Yamaha PA-150ANo original Yamaha spare part!The advantages of this external power adapter for Yamaha Epianos or workstations are      brand manufacturers     low residual ripple         Mechanical Description:The primary plug is designed for Europe and the plug on the secondary side is round with 5.5 mm outside diameter. Electrical properties:Secondary voltage: 12VDCCurrent: 2ACE / GS testedPractical advice:Plug of the device. Don't work under Voltage.

8 position rotary switch 16 mm widht suitable forYamaha RS-7000Mechanical Description:Technical Description:Practical advice:These rotary switch is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. Rotary Potentiometer vertikal 12 mm with center TapCenter Tap function: no deviation in center positionSubstitute rotary potentiometer forYamaha RS7000Pitch Bend, ENV.DEPTH,SWING VELOCITY, CLOCK SHIFT MIDI DELAY, BEAT STRETCH GATE TIMEElectrical properties:The nominal resistance has 10 kOhm (Kilo-Ohm), the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 12 mm bright, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has TAP function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin.Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. triple MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5046Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. used by:YamahaThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Complet replacement set potentiometer for Yamaha RM1xconsist of:8  pcs  rotary poti, vertikal, 12mm, Center click + TAP4  pcs  Encoder, 16mm1  pcs  Stereo Volume rotary pot, 14mmOperational Life for all pot's: 15.000 CyclesOperational Life for all Encoder: 50.000 CyclesMounting instruction Yamaha RM1x:in the RM1x Yamaha has installed a potentiometer without thread. The potentiometer I offer here can also be used in the RM1x. However, the housing holes must be drilled out by 1 to 2 mm and the axis must be shortened by 5 mm. The big advantage of this solution is that I think that threaded potentiometers are much more durable than unthreaded potentiometers. Undeniably, the axis is guided and supported by the thread much more stable.In the pictures you see a test installation I have made.The pot's  are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. new LCD Display suitable forYamaha Motif 6Yamaha Motif 7Yamaha Motif 8Yamaha RM1XYamaha RS7000This is only the LCD display without the backlight.The display is connected e.g. in the Yamaha RM1x by plugging the existing cable in the device onto the display. However, the display is supplied without the appropriate socket. Please note that you have to solder here.Original Yamaha spare part.The backlight is unfortunately no longer available. 

1 pcs. Yamaha Display Beezel WB21630RThe display of the instrument is screwed into this frame. The frame is then installed in the housing. 

Recapping set for Yamaha RX11The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Yamaha RX series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for the complete Yamaha RX11 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. IC MASK LHMN5UXX V1.01 RM1XSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. blue LCD Display with LED Backlight replacementYamaha RS7000We offer an absolutely equivalent display using modern LED technology for backlight.Plug and Play. No soldering is required.Color: White Character  /  Blue BackgroundDelivery scope of LCD Display for RS7000 :Display ready wiredInstruction for replacement Advantages of this special LCD display compared to the original display from Yamaha:The original Yamaha display consists of two individual components. Once the LCD display and a separate component, the backlight. The backlight is no longer available from Yamaha as a spare part. In the LCD display we offer here, the backlight is integrated. Originally two components become one component.We now have many years of experience with this type of LCD display. These displays are durable and robust. Notes on installation the Display in Yamaha RS7000 :To replace the display, the Yamaha RS7000 is opened from the back. So the rear half of the case has to be removed. Afterwards the floppy drive, the DM board and a sheet metal frame must be unscrewed. Everything is scraped and only a Phillips screwdriver, preferably PH2 is needed. Now the old display can be removed. Before installing the new display, three plastic lugs must be removed in the display frame. These can be broken off with pliers, or cut off with a knife. Please do not forget to clean the washer in the housing.No soldering required.All you need is a screwdriver, flat nose pliers and side cutters.