E-mu Systems
1 pcs. yellow LCD Display with LED Backlight replacement including cable Kit forE-mu E-IV We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: Black Character / yellow BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:This work is to be done only by technically, best electrotechnically savvy people.Installation service:We are also happy to install the display for you. Please ask.  Â
1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu DarwinWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  / black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask.Â
1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVE-mu e64We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: blue Character  / white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping is eliminated)lifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. In this case it must be desoldered.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people. Installation service:We are also happy to install the display for you. Please ask.
1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVE-mu e64We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  / yellow BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beeping is eliminated)lifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. In this case one part must be desoldered.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people. Installation service:We are also happy to install the display for you. Please ask.
1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu e5000 UltraWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  / white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask.Â
Phone Jack 1/4 inch- 6.3 mm, stereo, for printed circuit used by  E-Mu Orbit Vs Phone Jack in FrontTechnical descriptionThe offered phone jack for PCB mounting is a stereo jack without switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu DarwinWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  / white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation of LCD in Emu Darwin:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask.Â
1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu DarwinWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  / blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask.Â
1 pcs E-mu E64 mounting set for Hard DiscMounting kit to mechanically detach the hard drive from the enclosure.Attention: Only for old 3U rack devices. The new devices have different mounting points in the enclosure.With many of the E-Mu rack devices, the noise generated by the hard drive is a major problem. Particularly in quiet studio environments, the sound of the hard disc can be very disturbing.One noise will always remain. Whenever something moves, there is also a noise. The main advantage of our mounting set is that the hard drive and the hard drive vibrations are decoupled from the housing.Â
1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
1 pcs. OLED Display New forE-Mu Pro CussionTo replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display. Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
1 pcs. OLED Display New forE-Mu Pro CussionTo replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display. Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
1 pcs. OLED Display New forE-Mu Pro CussionTo replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display. Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
1 pcs. OLED Display New forE-Mu Pro CussionTo replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display. Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
1 pcs. OLED Display New forE-Mu Pro CussionTo replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display. Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
1 pcs. Phone Jack 1/4- 6.3 mm, stereo witch one Switch, for printed circuit used by E-mu E4KE-mu E-SynthE-Mu E4 XTE-Mu e6400Technical description:The offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
E-Mu EMAX II PSU Recapping SetThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage. Warning: Switching power supplies store high amounts of energy for long periods of time. You are working on assemblies that operate at 230 V AC and approx. 300 V DC.You are carrying out this work at your own risk and under your own responsibility.With an age of more than 30 years, the E-Mu EMAX series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers. Warning PSU Recapping:Risk of electric shock: Switching power supplys store high voltage and high energy for a very long period of time.When working with these spare parts offered here, you are working directly in a 230VAC circuit.Observe polarity. Incorrect installation will cause explosion and fire.For experts only: Be aware of dangers of electric currentÂ
E-mu
Founded in 1971 in Santa Cruz, California, USA, by two students, Dave Rossum and Scott Wedge, the company developed a patented, digitally sampled polyphonic keyboard in 1972, after first achieving financial success by building a modular synthesizer. Licensees for these keyboards were Oberheim and later Sequential Circuits. After a chequered history, E-mu was still convincing as a manufacturer of sound card chips in the 1980s, but also produced a well-known sampler, synthesiser and, above all, modular synthesiser systems, which were sold to such famous musicians as Herbie Hancock and Frank Zappa.
The most famous device produced by E-mu is probably the drum computer E-mu SP-12, and its successor SP-1200. Both devices are still very popular in the hip-hop and dance producer scene because of their rough lo-fi sound. Also, the strict timing of this device has always been praised.
But E-mu also had great success with the Emulator, a sampler that was launched as early as 1981. These devices were also used by the greats of the music industry at the time, and also brought a certain financial success.
Later, however, it was precisely this success that failed to materialise, and so the company with its numerous patents was bought up several times by other manufacturers
E-mu sampler spare parts in first-class quality
As is the case with many old devices, certain components of E-mu samplers are prone to weakening due to age.
For example, it is the displays that we often replace with modern LCD displays when the original displays are only barely legible. We offer different display versions for different E-mu devices, which differ in colour, for example. You can choose from four different displays with LED backlighting for your E-mu E4K, or your E-mu E-IV. When replacing a display, you should also consider replacing the devices internal battery, as the service life of devices from the 80s is probably already well over.
Another component that often reduces the fun of playing is the instrument or menu button. These were also not built to function until the end of the world.
Unfortunately, the power supply, which is used in many E-mu devices, namely the E-mu E4K, the E-mu E6400, in the E-mu E4 Platinum, to name but a few, also has a limited lifespan.
The replacement of such capacitors, buttons, batteries and regulators is carried out professionally and expertly in our specialist workshop by qualified employees.
Our spare parts are always of high quality, which will continue to ensure the function and sound of your equipment for a long time. They have either been ordered from the manufacturers of the original components or original assemblies, or, if this is not possible, replaced by fully compatible, tested components from other manufacturers. When procuring components of equal or higher value, we attach great importance to the highest quality in order to meet your demands as a musician or hobbyist.
Repair
In our specialist workshop we repair your E-mu instrument. We replace individual defective components and assemblies with new ones of the highest quality. Our specialists have been familiar with most of the devices for many years from their daily use, and are constantly learning about new devices and components. Further training is an important part of our daily work.
Our spare parts must not only be functionally convincing, they must also be perfectly compatible. We guarantee this through our own test procedures, which we use to test devices over several days with the new assembly or the new display.
Standard components such as capacitors, which, like batteries, also belong to the components in old synthesizers, samplers and drum machines that can only be attributed a limited lifespan, are also professionally replaced by those that have been specially designed and manufactured for use in audio equipment.
E-mu Systems has discontinued production and support in the field of musical instruments. Therefore, we offer first-class spare parts quality for E-mu Systems devices, from potentiometers, volume controls and sound cards to encoders, displays, buttons and capacitors. Either if you need spare parts or repair of your E-mu instruments, please contact us and make an appointment.