E-mu Systems
1 pcs. OLED Display New forE-Mu Proteus 1E-Mu Proteus 2E-Mu Proteus 3To replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
Recapping set for E-Mu Orbit V2The wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.This Recapping Set contains all necessary Capacitors for Switching Power Supply. Warning PSU Recapping:Risk of electric shock:Switching power supplys store high voltage and high energy for a very long period of time.When working with these spare parts offered here, you are working directly in a 230VAC circuit.Observe polarity. Incorrect installation will cause explosion and fire.For experts only: Be aware of dangers of electric current Â
1 pcs. duo-pole push switch in the switch design - OFF with solder Pins for Kable mounting suitable for modelsE-Mu - Mounting Frame must be taken overPlease note: Not suitable for all E-Mu devices.technical Dates:Voltage: 250VACCurrent: 6ATermination Solder VDE-tested Supplied without capMechanical Description:The housing of the switch is made of Plastic. The switch is provided for soldering. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 15 mm, a length of 30 mm and a height of 9 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A at 250 VAC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.
1 pcs. OLED Display New forE-Mu Vintage KeysAll you need to replace this display is a screwdriver. We supply the display itself ready for installation. The appropriate cable is soldered to the OLED display by us. To replace the display in the E-Mu Vintage Keys, open the lid of the instrument. The front panel must then be removed. The OLED display can then be replaced. Lifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.Â
1 pcs. Power cabel with 3Pol C13-plug VDE testedCable: H05VV-G3G0,75mm²Length: 1,8 m
1 pcs. triple MIDI DIN socket female 5 pin for printed circuit for E-MuJalco YKF51-5046 Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. This is a 1:1 replacement for the MIDI jack in most e-mu sampler.These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.
1 pcs. blue LCD Display with LED Backlight replacement including cable Kit forE-mu E4-XTE-mu e6400We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  / blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask.Â
1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E4XTE-mu e6400We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: black Character  / white BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask.Â
1 pcs. blue LCD Display with LED Backlight replacement including cable Kit forE-mu e5000 UltraWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  / blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:The display is prepared by us ready to plug in. All adjustments to the technical features of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. Our recommendation is to remove this part of the circuitry. It is sufficient to remove one or two components with a side cutter.However, we would like to point out that there is very little space in most units. This work should only be done by technically experienced people.Installation service:We are also happy to install the display for you. Please ask.Â
1 pcs. OLED Display New forE-Mu Ultra ProteusTo replace this display you need very good knowledge in soldering. The original display is soldered firmly to the board via a pin header. To disassemble the old display, this pin header must be cleaned very cleanly from the solder.An installation manual is enclosed with the display.These different Display versions are available:BlueRed/OrangeYellowWhiteLifetime:The lifetime is specified by the manufacturer with 40,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.
 1 pcs. Cap round 12 mm for tact switchThis cap for stylus has a diameter of 12 mm and a receptacle of 3 x 3 mm.Suitable as a spare part for E-Mu sampler
1 pcs. Slide potentiometer, suitable for E-mu E4KE-Mu E-SynthThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Slide Potentiometer with 60mm TravelThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. Slide Potentiometer with 20mm TravelNote on the Lever:The lever on the original potentiometer is made of metal. The potentiometer offered here has a plastic lever that is 0.6 mm thicker than the original. The lever must be slightly worked in the thickness so that the cap can be attached.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.
1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsE-mu Launch-Padtechnical Dates:Termination Solder PinSchwitch: OpenMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for this replacement.
1 pcs. tactile switch suitable for models E-mu Launch-PadThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton
1 pcs. new Blue LCD Display with LED Backlight replacement including cable Kit forE-mu E4KE-mu E-Synth We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes for installing the LCD display in the E-Synth::The display is prepared by us ready for plugging in. All adjustments to the technical specifications of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. We recommend removing this part of the circuit. In this case, an SMD transistor must be desoldered.We would nevertheless like to point out that there is very little space in most devices. This work should only be carried out by technically experienced individuals. Installation service for LCD Display:We are also happy to install the display for you. Please ask.Â
1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E4KE-mu E-SynthWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: Black Character  / White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementThe cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtion Notes for installing the LCD display in the E-Synth:The display is prepared by us ready for plugging in. All adjustments to the technical specifications of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. We recommend removing this part of the circuit. In this case, an SMD transistor must be desoldered.We would nevertheless like to point out that there is very little space in most devices. This work should only be carried out by technically experienced individuals. Installation service for LCD Display:We are also happy to install the display for you. Please ask.Â
1 pcs. yellow LCD Display with LED Backlight replacement including cable Kit forE-mu E4KE-mu E-Synth We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: Black Character / yellow BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement The cable must fit specifically to the instrument.Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes for installing the LCD display in the E-Synth:The display is prepared by us ready for plugging in. All adjustments to the technical specifications of the E-Mu sampler are made by us on the display. Plug and play installation. The new display is installed in exactly the same way as the old display was removed.Recommendation for backlight voltage: The original display required a separate voltage for the backlight. We recommend removing this part of the circuit. In this case, an SMD transistor must be desoldered.We would nevertheless like to point out that there is very little space in most devices. This work should only be carried out by technically experienced individuals.Installation service for LCD Display:We are also happy to install the display for you. Please ask. Â
1 pcs. PCB Connector 4 Pol, 2.5 mm PitchThis cable is ready assembled with a 14 pin board connector. The wires on the other side of the cable are stripped and tinned.technical hint:
1 pcs. white LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: Black Character  / White BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:This work is to be done only by technically, best electrotechnically savvy people.Installation service:We are also happy to install the display for you. Please ask.
1 pcs. new Blue LCD Display with LED Backlight replacement including cable Kit forE-mu E-IV We offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original.Color: White Character  /  Blue BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacement Benefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:This work is to be done only by technically, best electrotechnically savvy people.  Installation service:We are also happy to install the display for you. Please ask. Â
1 pcs. black LCD Display with LED Backlight replacement including cable Kit forE-mu E-IVWe offer an absolutely equivalent display using modern LED technology for backlight.The color of the shown display, may differ from the original. Color: White Character  / black BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of EL-Foillower power consumtionNotes on installation:This work is to be done only by technically, best electrotechnically savy people.Installation service:We are also happy to install the display for you. Please ask.
E-mu
Founded in 1971 in Santa Cruz, California, USA, by two students, Dave Rossum and Scott Wedge, the company developed a patented, digitally sampled polyphonic keyboard in 1972, after first achieving financial success by building a modular synthesizer. Licensees for these keyboards were Oberheim and later Sequential Circuits. After a chequered history, E-mu was still convincing as a manufacturer of sound card chips in the 1980s, but also produced a well-known sampler, synthesiser and, above all, modular synthesiser systems, which were sold to such famous musicians as Herbie Hancock and Frank Zappa.
The most famous device produced by E-mu is probably the drum computer E-mu SP-12, and its successor SP-1200. Both devices are still very popular in the hip-hop and dance producer scene because of their rough lo-fi sound. Also, the strict timing of this device has always been praised.
But E-mu also had great success with the Emulator, a sampler that was launched as early as 1981. These devices were also used by the greats of the music industry at the time, and also brought a certain financial success.
Later, however, it was precisely this success that failed to materialise, and so the company with its numerous patents was bought up several times by other manufacturers
E-mu sampler spare parts in first-class quality
As is the case with many old devices, certain components of E-mu samplers are prone to weakening due to age.
For example, it is the displays that we often replace with modern LCD displays when the original displays are only barely legible. We offer different display versions for different E-mu devices, which differ in colour, for example. You can choose from four different displays with LED backlighting for your E-mu E4K, or your E-mu E-IV. When replacing a display, you should also consider replacing the devices internal battery, as the service life of devices from the 80s is probably already well over.
Another component that often reduces the fun of playing is the instrument or menu button. These were also not built to function until the end of the world.
Unfortunately, the power supply, which is used in many E-mu devices, namely the E-mu E4K, the E-mu E6400, in the E-mu E4 Platinum, to name but a few, also has a limited lifespan.
The replacement of such capacitors, buttons, batteries and regulators is carried out professionally and expertly in our specialist workshop by qualified employees.
Our spare parts are always of high quality, which will continue to ensure the function and sound of your equipment for a long time. They have either been ordered from the manufacturers of the original components or original assemblies, or, if this is not possible, replaced by fully compatible, tested components from other manufacturers. When procuring components of equal or higher value, we attach great importance to the highest quality in order to meet your demands as a musician or hobbyist.
Repair
In our specialist workshop we repair your E-mu instrument. We replace individual defective components and assemblies with new ones of the highest quality. Our specialists have been familiar with most of the devices for many years from their daily use, and are constantly learning about new devices and components. Further training is an important part of our daily work.
Our spare parts must not only be functionally convincing, they must also be perfectly compatible. We guarantee this through our own test procedures, which we use to test devices over several days with the new assembly or the new display.
Standard components such as capacitors, which, like batteries, also belong to the components in old synthesizers, samplers and drum machines that can only be attributed a limited lifespan, are also professionally replaced by those that have been specially designed and manufactured for use in audio equipment.
E-mu Systems has discontinued production and support in the field of musical instruments. Therefore, we offer first-class spare parts quality for E-mu Systems devices, from potentiometers, volume controls and sound cards to encoders, displays, buttons and capacitors. Either if you need spare parts or repair of your E-mu instruments, please contact us and make an appointment.