Keyboards

JST FJ socket 5 pin for printed circuitthis FJ Socket form JST is used by Technics E-Pianos for connecting Printid Circuit Boards. Pitch: 2.0 mmThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Mini Din plug male 8 pin for printed circuitthis mini din plug is used by Technics E-Pianos for connecting foodswitch. Technics used two different Mini DIN plugs. It can be a 4 pole or a 8 pole version.These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Mini Din socket female 4 pin for printed circuitthis mini din Plug is used by Technics E-Pianos for connecting foodswitch. Technics used two different Mini DIN sockets. Sometimes it is a 4 pole or in other cases it is a 8 pole socket.These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

MIDI DIN socket female 5 pin for printed circuitused in: Korg SP250 These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Cable with plugs QEXG-VH06015 for Technics Speaker, usedTechnics SX-PX101Technics SX-PX103Technics SX-PX111This cable is used inside the E-Piano to connect Speaker in E-Piano Stand.

1 pcs. Phone Jack 1/4 inch- 6.3 mm, mono with switch, for printed circuitHosiden HLJ7101-01-3010 This phone jack is no longer manufactured and there are only remaining stocks.This part is used inRoland Fantom FARoland Fantom S88Roland Fantom X6Roland Fantom X7Roland Fantom X8Technics E-PianosTechnics KeyboardsPlease have a very detailed view on the picture. There is one Phone Jack very similar.Technical descriptionThe offered phone jack for PCB mounting is a Mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

Single-pole push switch in the switch design - OFF with solder pins for PCB mounting suitable for modelsKorg Korg Part Number:The power switch corresponds to the ALPS switches SDDLD12200 TV3. This is no longer manufactured by ALPS.Termination Solder pinMounting PCBVDE-tested Supplied without capMechanical Description:The housing of the switch is made of nylon 66. The switch is provided for PCB mounting. Therefor are tow solder pins as Snap-In pins in the front. The spacing of the snap in pins is 16 mm. The housing cut job of performing the switching element should be 4x4 mm. The switch itself has a width of 10 mm, a length of 27 mm and a height of 17.90 mm. The protruding switching element has a length of 18 mm. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder connections for cable assembly. The length of the terminals is 4.2 mm and a width of 3 mm.The electrical load is 4 A at 250 VAC.Knowledge in soldering is required for switch replacement.

DC Power Plug suitable for modelsRoland EP7 IItechnical Dates:Termination SolderingMechanical Description:The housing of the Power Plug is made of Plastic and cable is soldered on it.  Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 5 A.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for switch replacement.

1 pcs. DC Power Jack with solder Pins for PCB mounting suitable for modelsE-mu Launch-Padtechnical Dates:Termination Solder PinSchwitch: OpenMechanical Description:The housing of the Power Jack is made of Plastic and the jack is provided for P.C.B. mounting. Electrical properties:The electrical components are made of copper with a silver or tin plating. The electrical connection is made with solder pins.The electrical load is 2 A at 24 VDC.Practical advice:Plug of the device. Don't work under Voltage.Knowledge in soldering is required for this replacement.

1 pcs. Transformer Technics PX101, PX103, PX111This Transformer is usedd and in a good condition.The primary cause of a defective, e.g. To make matters worse, most devices are only protected on the primary side of the transformer with a microfuse. In this situation, the transformer operates in overload, which in turn leads to overheating of the transformer.

1 pcs. Transformer Technics PX107This Transformer is usedd and in a good condition.The primary cause of a defective, e.g. To make matters worse, most devices are only protected on the primary side of the transformer with a microfuse. In this situation, the transformer operates in overload, which in turn leads to overheating of the transformer.

1 pcs. Transformer Technics PX73This Transformer is usedd and in a good condition.The primary cause of a defective, e.g. To make matters worse, most devices are only protected on the primary side of the transformer with a microfuse. In this situation, the transformer operates in overload, which in turn leads to overheating of the transformer.

LED-tactile switchLED colour: yellowThe construction part is not longer built. The old serial number was KHJxxx. With that serial number the part was built during the 80s.Be sure to take care of the polarity while inserting the part:The long pin is the positive pole (anode), the short pins are the negative pole (cathode).The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Mainboard repair with expansion QJBG2150 for Technics E-PianosTechnics SX-PX107These Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.

tactile switch with green LED suitable for modelsRoland JV-1000   only Patch-GroupPart No.: 13119708This switch fits also for this:Roland JV-1000 Edit/Track    difference: orange LEDThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Dual Button for 12 x 5 mm Window Roland HP-900Roland HP-1700Roland KR-3000Roland U-20Do you know this: the button you activate don't react. This processs starts slowly and in the beginning do don't recognice it. Later you start to activate the buttons harder and harder. Then, one day the button will broke. The reasen for this is a worn out tact switch under the user button. When you replace the tact switch all will be fine in future.Technical Description:This Button fits for many Roland Instruments and is build for a Casing Window of 12 x 5 mm. This part has two Buttons and each button has a window for LED Light.Practical tip:This button sits between PCB and Cassis. In munch cases the button is fixed with tape. Other Manufacturer fix this parts with adhesive.

Fader knob for Roland SH201This fader knob fits for all fader on Roland SH201.This part is no longer aiviable.Original Roland spare part, newRoland spare part number: 4233323

1 pcs. Mainboard repairing for Technics E-PianosTechnics SX-PX101Technics SX-PX111These Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard. 

1 pcs. Tactile switch with blue button and red LED suitable forSequential Circuits Prophet VSThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Tactile switch with black button suitable forSequential Circuits Prophet VS The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

1 pcs. Tactile switch with blue button suitable forSequential Circuits Prophet VSThe buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

tactile switch suitable for modelKorg DVP-1Korg EX8000Korg SDD-2000 und Korg SDD-3000Roland Fantom X6, X7 und X8Roland MC307Korg replacement part no: 37504800Roland  replacement part no: 894645The construction part is not longer built. The old serial number was KEC10010 With that serial number the part was built during the 1980s.The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton

Mainboard for Technics E-Pianos Technics SX-PR170Technics SX-PR270Technics SX-PR370These Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.

Amplifier/Power Supply Board for Technics E-PianosTechnics SX-PR170Technics SX-PR270Technics SX-PR370These Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.