Access Virus Indigo

Contact rubber for Fatar KeyboardsFatar uses in many different keyboards same contact rubber. The here offered contact rubber are suitable for!!!!!   Not for use in Roland Instruments    !!!!!Fatar TP/7SFatar TP/8SFatar TP/9SFatar TP/10 MDRFatar TP/10 ABSFatar TP/40Fatar TP/100LRtechnichal dimensionsNo of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white or greyFatar Keyboards are used by Clavia Nord, Döpfer, Ensonic, Korg, Kurzweil, GEM

Phone Jack 1/4 inch- 6.3 mm, stereo with switch, for printed circuit used in  Korg, Roland or Yamaha Instrumentsthis phone jack corresponds to these parts:YKB21-5074SCJ630P5PJ603Technical descriptionThe offered phone jack for PCB mounting is a stereo jack with switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip:These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

1 pcs. CR2032Attention: Shipping for Europe only Technical Description:The dimensions of CR2032 are diameter of 20 mm and a thickness of 3mm. Manufacturer: Panasonic or Varta Information for handling old Battery's

1 pcs. Access Virus Rotary Potentiometer vertikal 11x11 mm. 10kOhm Electrical properties:The nominal resistance has 10 kOhm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 11 x 11 mm, the total length without pins is 25 mm. In this total length the casing is 7,5 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 12 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The four solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The bented pins, which are sticking out to the front, are necessary for the electrical function, in which the fourth pin has no electrical function.In the back range of the casing the metallic edge-socket connector is mounted. The connector will be fixed at the printed circuit board by pressing in the snap in pin. Between the two snap in holdings the distance is 13 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it.  

1 pcs Acess Virus Single pole rocker switch with solder lugs 6A / 250VACTermination Solder Lug1 poleMounting hole: 19,8 x 12,8 mmDimensions outside: 20,8 x 14,8 mmVDE-tested Mechanical Description:The switch housing consists of polycarbonate. The switch is provided for a snap-in mounting in a housing and having corresponding spring lips on the narrow side of the housing. Housing cutout for installation should be 19.30 mm x 12.90 mm. The switch itself has a width of 12.90 mm, a length of 18.50 mm and a height of 13.60 mm plus 3 mm height of the rocker. The outside dimensions are 20.8 mm x 14.8 mm.Electrical properties:The electrical components are made of copper with a silver or tin plating and electrical connection is made with solder lugs for cable assembly. The length of the terminals is 2.9 mm with a width of 3 mm.The electrical load is 6 A at 250 VAC.Knowledge in soldering is required for switch replacement.

1 pcs. Acess Virus Sysnthesizer tactile switchFor the repair and maintenance of your Access Virus synthesizer. Perfectly fitting buttons with a very long service life.The buttons are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.why should I solder new pushbutton