Yamaha CLP-Serie

Pedal Assembly for Yamaha E-Pianos XR780On this Pedal the PCB is fittet with Ground cable.Practice tip:Yamaha has built in a socket on the boards, which are built into the pedal which is perpendicular to the board. Here, the cable is plugged in that leads to the electronics of the electric piano in the upper part. As a result, this beech breaks out in the course of the operating years and it comes to the failure of the pedal.In most Repartur cases, it will be enough just to swap the socket.Depending on the model, this pedal was supplied with a potentiometer or contact rubber in the damper pedal. Please be sure to check the pedal before ordering a replacement part. 

1 pcs. Yamaha FUSTB AC-IN BoardFor Europe only: 230VACUsed inYamaha CLP-575 

1 pcs. Yamaha Pedal screwDimensions: M6 x 57 mmNote:At 38 mm, this pedal support bolt has a longer thread than the one under item numberSCYA-WF054500

1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha CLP-120Yamaha CLP-430Yamaha CLP-920Yamaha CLP-990Yamaha P-105Yamaha P-120 The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Yamaha USB Socket Typ B PCBJalco used by: Yamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 pcs. Rotary Potentiometer suitable forYamaha N1 Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 9.5 x 11 mm, the total length without pins is 29 mm. In this total length the casing is 16 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 10 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of brass. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M7 x 0,75 mm.The nine solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2,5 mm. The pins, which are sticking out  are necessary for the electrical function. Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs Yamaha Contactrubber 88P newThis contact rubber was installed in different Yamaha keyboards and there are different spare part numbers for this spare part.A note about the contact rubbers: The contact rubber for the 88's keyboard was available in the colors pink and green. The pink contact rubber is missing 2 holes in the rubber which serve as a guide.The green version is no longer available.Note for the installation of the Yamaha contact rubber:Please pay attention to the installation position! The interruptions in the Konaktstreifen are not symmetrical. 

1 pcs Yamaha contactrubber Wood key 12 contactsIn this wooden keyboard installed by Yamaha only in very few models, a contact rubber was used in two places.Once there is a contact rubber in the front under the wooden keys. A second Kontaktugmmi sits in the back under the hammers.Here it is the contact rubber at the front under the keys. No more rubbers available.Contactrubber for one actave with 12 contacts.Only some few parts availableThis rubber was used inYamaha CLP-175Yamaha CLP-990Yamaha CVP-900

1 pcs. Slidepotentiometer. Suitable for Volume Slider inYamaha CLP-545Yamaha CLP-565GPYamaha P-125This potenziometer is used for volume control, but it is a mono potenziometer. Not Stereo and this is correct in this case.The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Yamaha Pedal screwDimensions: M6 x 57 mm Note:At 25 mm, this pedal support bolt has a shorter thread than the one under item numberSCYA-ZY898700

Replacement Keys for Yamaha NL2 KeyboardThese Keys fits for all Yamaha NL2 keyboards.Yamaha NL2 keyboard is used in:Yamaha CP5Note on the keys supplied:The keys are delivered without the black rubber that is mounted at the bottom of the key. The black rubber is taken from the old key. The rubber is clicked in and can be easily replaced. The Yamaha NL2 keyboard is a velocity-sensitive keyboard. The keys have a wooden core that is covered with plastic.Mechanical construction:The base frame of the keyboard is made of plastic and is therefore very light. All other components are attached to this frame by screws or clamps.The white Keys have a size in cm of 2,2x21x4,2, the black Keys 2,2x19,2x5,9 cm.

1 pcs. Slidepotentiometer with center click suitable for Yamaha CLP-150Yamaha CLP-170The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. Flash ROM 16Mas replacement for MBM29LV160BE90TN Mechanical Description:This flash rom is housed in a TSOP48 package and is designed for SMD mounting on a circuit board. This part sensitive to static charge  

1 pcs. Slidepotentiometer. Suitable for Brillinace Slider inYamaha This slider has center clickThe slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

Replacement Hammer for Yamaha GHD Keyboard The Yamaha GHD Keyboard is used in two different configurations.The Keyboard is availabel with a 1 zone Hammeraction and with a 4 Zone Hammeraction.Here you will find the different Hammer for the GHD Keyboard

1 piece Yamaha Pedal PCB X0193 for E-Pianos V7675600This PCB for Yamaha pedal unit is used in pedals in which three potentiometers are installed.For final use, parts on the board still have to be broken off. The break edges are marked and perforated accordingly. This can be done easily and without tools. 

Recapping setYamaha MA60 Recapping Set PSUThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.If no longr available from Nichicon we use Würth or Rubycon Capacitors.This Recapping Set contains all necessary Capacitors for the PSU.The Capacitors are firmly soldered to a circuit board. For replacing the capacitor craftsmanship and experience in soldering is required. 

1 pcs. VR ACTUATOR for Yamaha XR780 Pedal Assembly

1 pcs. CIRCUIT BOARD DM CLP-440MSemiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. POWER SWITCH ASSY CLP-170Semiconductors and electronic assemblies are sensitive to electrostatic charge. Please observe the regulations on ESD handling.The exchange and return of semiconductors and electronic assemblies is excluded after opening the packaging.

1 pcs. 1,44 MB Disc ALPS DF354H 

1 pcs. Replacement stereo rotary potentiometer 14mm suitable forYamaha CLP-150Yamaha P-250Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 7,5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Yamaha FU80 AC-IN BoardFor Europe only: 230VAC

1 pcs. Mainboard for Yamaha CLP-150 E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.