Yamaha

1 pcs. LCD Display black brandnew forYamaha TG55this is  a plug in ready Display replacement for Yamaha TG55 . You will only need a screwdriver for this replacement.We deliver this LCD Display plug in ready.With this Display we deliver some Parts for easy mounting and a short Instruction Manual.These different Display versions are available:BlueWhiteBlackYellowLifetime:The backlight lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. LCD Display yellow brandnew forYamaha TG55this is  a plug in ready Display replacement for Yamaha TG55 .We deliver this LCD Display plug in ready.With this Display we deliver some Parts for easy mounting and a short Instruction Manual.These different Display versions are available:BlueWhiteBlackYellowLifetime:The backlight lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity.

1 pcs. triple MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5046Please look carefully. This MIDI socket is also available in a version in which the DIN sockets are rotated by 180 degrees. used by:YamahaThese part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Complet replacement set potentiometer for Yamaha RM1xconsist of:8  pcs  rotary poti, vertikal, 12mm, Center click + TAP4  pcs  Encoder, 16mm1  pcs  Stereo Volume rotary pot, 14mmOperational Life for all pot's: 15.000 CyclesOperational Life for all Encoder: 50.000 CyclesMounting instruction Yamaha RM1x:in the RM1x Yamaha has installed a potentiometer without thread. The potentiometer I offer here can also be used in the RM1x. However, the housing holes must be drilled out by 1 to 2 mm and the axis must be shortened by 5 mm. The big advantage of this solution is that I think that threaded potentiometers are much more durable than unthreaded potentiometers. Undeniably, the axis is guided and supported by the thread much more stable.In the pictures you see a test installation I have made.The pot's  are firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.

Recapping set for Yamaha TX802Attention: 110V US VersionThe wear parts of the electronics are electrolytic capacitors. Capacitors are aging, and you will see the effect at first when it comes to greater damage because of overvoltage.With an age of more than 30 years, the Yamaha TX series is in any case one of the instruments in which an replacement of all electrolytic capacitors is strongly advised.Our recapping set is made up of Capacitors, which have been specially developed for use in audio applications. The manufacturer Nichicon is for us the manufacturer with a good quality at reasonable prices offers.This Recapping Set contains all necessary Capacitors for complete recapping of Yamaha TX802 The Capacitors are firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required. 

1 pcs. Yamaha Montage Scene Rotary PotentiometerYamaha Montage 6Yamaha Montage 7Yamaha Montage 8Yamaha YC73Yamaha YC88Electrical properties:The stereo nominal resistance has 5 Kilo-Ohm, the electric resistance gradient is liniear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 10,5 x 11 mm, the total length without pins is 26,5 mm. In this total length the casing is 10 mm long. On this casing is the thread with 5 mm length connected and out of the thread the axis rises with 12,5 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of Metall. Its head has ends in corner radius. The thread, which surrounds the axis, has the screw measure M9 x 0,75 mm.The three solder pins are 0,6 mm wide (one of them) and they are arranged in one row in a distance of 2,5 mm (pitch).At the end of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 10,5 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The Potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. 1,44 MB Disc ALPS DF354H 

1 pcs. double MIDI DIN socket female 5 pin for printed circuitJalco YKF51-5054 rotated 180 degreeused by: KorgRolandYamaha These part is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Price is for 1 piece.

1 pcs. Replacement stereo rotary potentiometer 14mm suitable forYamaha CLP-150Yamaha P-250Electrical properties:The stereo nominal resistance has 10 KOhm, the electric resistance gradient is linear. The potentiometer is construed for a power of 0,05 Watt.Appearance (technical characterisation):The casing measures 14 mm widht, the total length without pins is 20 mm. In this total length the casing is 7,5 mm long. The axis rises with 13 mm length. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of black plastic. Its head has a slot and ends in corner radius. The seven solder pins are 0,6 mm wide (one of them) and they are arranged in a distance of 2 mm (pitch). The curved pins, which are sticking out to the front, are necessary for the electrical function.In medium range of the casing the metallic snap in connector is mounted. These connector will fix the potentiometer at the printed circuit board by pressing in.Between the two snap in holdings the distance is 15,3 mm. The holders latch in the board and fix the potentiometer mechanically.Useful hint:The volume control is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Yamaha FU80 AC-IN BoardFor Europe only: 230VAC

1 pcs. Yamaha switching Power Supply repair for MX 100 II DisklavierFrom our practical experience we know that this power supply unit, which is installed in the MX 100 II Disklavier from Yamaha, shows age-related defects. As a rule, this manifests itself in the complete failure of the power supply in this Yamaha Disklavier.Our Service:We can offer you the repair of this power supply unit. For the repair, it is sufficient if you have the power supply unit removed by a specialist electrical engineering company and send it to us. We will check and repair the power supply unit in our workshop.Safety notice:Switching power supplies store high voltages of approx. 300 volts DC over a long period of time. This spare part is only for specialists with appropriate knowledge of electrical engineering.  

1 pcs. LCD Display brandnew forYamaha DX7this is  a plug in ready Display replacement for Yamaha DX7. You will only need a screwdriver for this replacement.These different Display versions are available:BlueOrangeWhiteFor this replacement you will only need a screwdriver. We deliver this LCD Display plug in ready.Attention on the Orange Display: Here, a height difference of 3 mm must be bridged or compensated.Lifetime:The lifetime is specified by the manufacturer with 50,000 operating hours. After this specified drive time, the display still has 50% of its original luminosity. 

1 pcs. Yamaha switching Power Supply for HQ100SX DisklavierFrom our practical experience we know that this power supply unit, which is installed in the HQ100SX Disklavier from Yamaha, shows age-related defects. As a rule, this manifests itself in the complete failure of the power supply in this Yamaha Disklavier.Our Service:We can offer you the repair of this power supply unit. For the repair, it is sufficient if you have the power supply unit removed by a specialist electrical engineering company and send it to us. We will check and repair the power supply unit in our workshop.Safety notice:Switching power supplies store high voltages of approx. 300 volts DC over a long period of time. This spare part is only for specialists with appropriate knowledge of electrical engineering.  

1 pcs. Yamaha Tyros 5 Mainboard

1 pcs. Contactrubber GH 2M suitable forYamaha CP1

LCD Display with LED Backlight replacement including cable Kit forYamaha TG77We offer an absolutely equivalent display using modern LED technology for backlight.Color: Black Character  /  yellow BackgroundDelivery scope:Display ready wiredMounting partsInstruction for replacementBenefits for this Display with LED Backlight:much brighterhigh-frequency noise (beepingis eliminatedlifetime of LED Backlight is around 3 times higher than lifetime of  EL-Foillower power consumtionNotes on installation:Inside Yamaha TG 77 is very little space for the new display. A circuit board is mounted behind the display, it is called switch panel. On this switch panel a number of diodes are soldered which can collide with the new display. It is highly advisable to move these diodes to the back of the switch panel.This work is to be done only by technically, best electrotechnically savvy people.

1 pcs. Mainboard for Yamaha CVP-207 E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard. 

1 pcs. Mainboard for Yamaha CVP-209 E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard. 

1 pcs. Rotary Potentiometer suitable forYamaha CVP-203Yamaha CVP-205Yamaha CVP-207Yamaha CVP-209 Electrical properties:The nominal resistance has 10 Kilo-Ohm, the electric resistance gradient runs linear.Appearance (technical characterisation):The casing measures 14 x 11 mm, the total length without pins is 15 mm. In this total length the casing is 6 mm long. The axis has a diameter of 6 mm and is flattened on a length of 7 mm. It is made of brass. Its head has ends in corner radius.The nine solder contact pins are 0,8 mm wide (one of them) and they are arranged in a raster in a distance of 2 mm. The pins, which are sticking out  are necessary for the electrical function. Useful hint:The potentiometer is soldered on the circuit board. You should have mechanical skills and experience in soldering to replace it. 

1 pcs. Slider with 45mm Travel. Suitable for Yamaha Motif ES CS 1 - 4Yamaha Motif XS Volume 1 - 8The slider is firmly soldered to a circuit board. For replacing the button craftsmanship and experience in soldering is required.

1 pcs. brand new 10 inch extern LCD Display for Yamaha CVP seriesYamaha has been using color displays of various sizes in the Clavinova CVP models for many years. Displays are subject to natural aging, which leads to the fact that the displays are increasingly difficult to read. Even a readjustment of the contrast is no longer sufficient at some point. Yamaha has a very good spare parts supply for the Clavinova series. However, Yamaha cannot supply the original displays as replacements in all cases.We offer here an external HD LCD display that connects to the external video out of your Yamaha Clavinova CVP model. This ecternel Display shows same screen information as internal Display.The display resolution must be adjusted in many cases from 4:3 to 16:9 so the new display may be slightly blurred.Not an original spare part from Yamaha.Scope of delivery for extern Yamaha Clavinova LCD:1 pc. new LCD display, stand and cable for EU Attention: The color of the display shown may differ slightly from the original.  Notes on disposal:Each electronic component contains important raw materials that should be recycled. Please find out where in your area there is a corresponding collection point for these components. 

1 pcs. brand new LCD Display with backlight suitable forYamaha CP4 Stage PianoYamaha CP40 Stage PianoWe offer here the original Yamaha spare part. Scope of delivery:1 pc. new LCD display, ready wired Notes on installation:Please be aware that you are opening an electrical device that is supplied with 230 volts. This work should only be carried out by people who have the appropriate expertise. Notes on disposal:Each electronic component contains important raw materials that should be recycled. Please find out where in your area there is a corresponding collection point for these components. 

1 pcs. Mainboard for Yamaha CLP-150 E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard. 

1 pcs. Mainboard for Yamaha CLP-170 E-PianosThese Mainboard is tested by us and fully working. We sell it with one year warranty.Is your e-piano faulty or no sound?Even if we do not have the appropriate board in stock, we can repair your board - with warranty. Usually it is enough if you send us the mainboard and the AmpBoard.