Roland Juno Serie

1 pcs. Varta Battery with solder tail suitable for  Roland Juno 60Please check right polarity! Attention: Shipping for Europe only The solder tail is about 0.5mm too wide to fit through the slot in the circuit board.The batterie is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required.Information for handling old Battery's

1 pcs. Push Switch with solder Pins for PCB mounting suitable forRoland Juno 60 - Hold, Arpeggiotechnical Dates:Termination Solder PinSupplied without capPractical advice:Knowledge in soldering is required for switch replacement.

1 piece LED 3 mm Greenin 

1 pcs. Contact rubber for Roland SK3 KeyboardsRoland has built in his keyboard instruments built in the 1990's essentially always the same keyboard. Fortunately, there are still contact rubbers for this keyboard today. These contact rubbers are NEW.technichal dimensions for contact rubber:No of contacts: 12 or 13Width: 22.7 mmheigh: 6.5 mmColor: white or greytechnical description of Roland SK3 contatct rubber:A contact rubber with 12 contacts covers one octave. The contact gumi with 13 contacts is needed once in a 61' keyboard. All contact strips are mechanically divided into blocks of 4 contacts. A contact rubber can always be divided or cut off at the end of a 4's block.Number of contact rubbers needed for a complete keyboard.61 keys: 4 x 12 contacts and 1 x 13 contacts76 keys 7 x 12 contacts88 keys 8 x 12 contacts 

1 pcs. Roland Juno 106 Display Bezel red newThis display bezel can replace the original display bezel on the Roland Juno-106. Due to the age of the Roland Juno-106 synthesiser, it is possible that the original bezel is scratched. It is also possible that the plastic has become brittle and must be replaced for this reason. Note on mounting the display bezel in the Roland Juno 106:It is best to use double-sided adhesive tape to stick the new display bezel in place. This adhesive tape can be purchased in suitable widths of e.g. 2 mm.

1 pcs. Roland Juno 106 Display Bezel clear newThis display bezel can replace the original display bezel on the Roland Juno-106. Due to the age of the Roland Juno-106 synthesiser, it is possible that the original bezel is scratched. It is also possible that the plastic has become brittle and must be replaced for this reason.Note on mounting the display bezel in the Roland Juno 106:It is best to use double-sided adhesive tape to stick the new display bezel in place. This adhesive tape can be purchased in suitable widths of e.g. 2 mm.

1 pcs. Phone Jack 1/4 inch- 6.3 mm, mono with switch, for printed circuit used Roland or Yamaha InstrumentsPay attention! The solder contacts are arranged staggertly.The item is the same asHLJ 0521-01-1110HLJ 0541-01-1110HLJ 1520-01-3110HLJ 1540-01-3110This part is used inRoland Ersatzteilnummer 13449125  Yamaha Ersatzteilnummer LB203090Yamaha Ersatzteilnummer LB301930Technical description:The offered phone jack for PCB mounting is a mono jack one switching contact for 1/4 inch. The housing is made of black synthetic material and the electrical parts are made of a copper alloy with a tin coating. Praktikal tip for phone jack:Pay attention! The solder contacts are arranged staggertly.These phone jack is firmly soldered to a circuit board. For replacing craftsmanship and experience in soldering is required. 

1 piece 7-Segment with 2 Digits, Redthis 7-segment with 2 digits fits perfect in these InstrumentsRoland Juno 106The Items are firmly soldered to a circuit board. For replacing  craftsmanship and experience in soldering is required.